15th Jul 2010, 4:38 pm | #81 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Update:
Still measuring trying to find that elusive component which is giving me grief. I cleaned the line hold, the vertical hold, and put in a new 30P4 and U191. Still running with 7.6KV, 290V A1 Some voltage readings:- R116 should be 120V but is 99V C110 should be 72V but is 101V R114 I think shoudl have 100V but on one side has -25V sometimes its - 1785mV on the other side of R114 nowt! Last edited by oldticktock; 15th Jul 2010 at 5:00 pm. |
15th Jul 2010, 4:54 pm | #82 |
Dekatron
Join Date: Sep 2003
Location: Bolton, Greater Manchester, UK.
Posts: 6,644
|
Re: GEC BT1156 First Light & Vidor CN4216
Change R12. Also, if there are any resistors on the ends of the line hold control, change these too.
Then try it. Cheers, Steve P,
__________________
If we've always had it, why is the Car Boot open? You're not sneaking another Old TV in are you...? |
15th Jul 2010, 5:03 pm | #83 |
Heptode
Join Date: Jul 2009
Location: Stoke-on-Trent, Staffordshire, UK.
Posts: 719
|
Re: GEC BT1156 First Light & Vidor CN4216
You're very close Chris !
Did you do as post 80? What did you find ? Not just the resistors, the pot may have changed value.... they do sometimes. Did you try a temporary silicon rectifier? If your HT is still low either the rectifier or the reservoir capacitor are suspect, the line frequency is now very close. I see there are also some add-on dropper resistors... check they are the correct resistance values against the circuit.. It was very common for field service engineers to fit what they had in the van if that got the set working, rather than run the set in to the workshop or come back with correct parts. HTH Pete |
15th Jul 2010, 5:15 pm | #84 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
I have checked may resistors and posted results all were within 20%
Is R114 not odd? the service sheet states 100V ? I did not add the IN4007 as per advice post #27 Teleman, Fenseh, Pete, Steve and Trevor, I will re-check back on all advice given so as not to have missed any of your valuable input or not to have followed advice. cheers guys My head hurts |
15th Jul 2010, 5:31 pm | #85 |
Dekatron
Join Date: Sep 2003
Location: Bolton, Greater Manchester, UK.
Posts: 6,644
|
Re: GEC BT1156 First Light & Vidor CN4216
When your head hurts, stop. It's not a job. Honest guv.
Resistors go high in value, so if they have all gone high, that may be enough to put it out of range. Any that are more than 10% out, change, Check with the service sheet as to the correct value too, Have a rest for now though, A tired worker makes mistakes. R114 - That scope trace is 100v in total, The DC value will be slightly lower. Cheers, Steve P.
__________________
If we've always had it, why is the Car Boot open? You're not sneaking another Old TV in are you...? |
15th Jul 2010, 5:37 pm | #86 |
Dekatron
Join Date: Sep 2006
Location: Kilmarnock, Ayrshire, UK.
Posts: 5,420
|
Re: GEC BT1156 First Light & Vidor CN4216
Hi Chris.
That picture looks "nearly" locked so I would be looking at the line sync feed, the sync seperator is working as your frame is locked ok, so its the small value caps from the sync seperator to the line stage to check
__________________
Cheers, Trevor. MM0KJJ. RSGB, GQRP, WACRAL, K&LARC. Member |
15th Jul 2010, 5:45 pm | #87 |
Heptode
Join Date: Jul 2009
Location: Stoke-on-Trent, Staffordshire, UK.
Posts: 719
|
Re: GEC BT1156 First Light & Vidor CN4216
Steve is right, when your head's bursting it's time for a rest.
Not sure what you mean about R114. The service sheet shows a waveform that's 100v peak to peak when seen on a 'scope. It will be measured with the timebsase locked, which you haven't quite got yet. There will be a necative DC voltage here if you measure with a meter, but it won't be 100v. As the waveform is a high frequency one it can cause some meters to get upset, and then you can get all sorts of readings. The makers usually specified what meter they used, and it was nearly always an AVO 7 or 8 depending on the vintage. That way, if the meter got upset or modified the voltage being measured due to its own resistance, you should still get the same reading as they did. It also gave a guide as to meter sensitivity required for those who had cheaper or just different instruments. Quick question... is the line hold pot right at the end? QQ 2 Is the picture stationary with those horizontal (i.e. zigzag) lines, or is it rolling sideways / vertically ? Pete |
15th Jul 2010, 5:53 pm | #88 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
A1, Line hold is almost fully advanced just backed off a tad
A2, picture is unstable sometimes it's there, then its off again scrolls vertically. |
15th Jul 2010, 6:35 pm | #89 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Lucky i'm stuborn and just can't give up
Not having enough experience yet, I don't know what that displacement at the top is Now can I move onto finding out why the HT and EHT are low? Chris Last edited by oldticktock; 15th Jul 2010 at 6:44 pm. |
15th Jul 2010, 6:46 pm | #90 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Left running for a while it eventually deteriorates to this
I forgot to measure EHT & A1 I've switched off and will wait a while then measure both scenarios. |
15th Jul 2010, 6:54 pm | #91 |
Dekatron
Join Date: Sep 2006
Location: Kilmarnock, Ayrshire, UK.
Posts: 5,420
|
Re: GEC BT1156 First Light & Vidor CN4216
Hi Chris
The line sync is weak so your not getting a good solid lock, I am just going out to the shed so I will have a gander at the circuit and give some pointers.
__________________
Cheers, Trevor. MM0KJJ. RSGB, GQRP, WACRAL, K&LARC. Member |
15th Jul 2010, 7:00 pm | #92 |
Heptode
Join Date: Jul 2009
Location: Stoke-on-Trent, Staffordshire, UK.
Posts: 719
|
Re: GEC BT1156 First Light & Vidor CN4216
You need to be able to go from below to above line freq by adjusting the hold control, in which case you would pass through a region of having a single "floating" picture, even if there's no sync. I'm sure you'd have told us if you can do this.
Watch what happens when you turn the line hold the last little bit. If the slope of the bars becomes more nearly vertical it's a sign you are going in the right direction. The picture may then look less stable because at the moment it's trying to lock at line frequency minus an harmonic of frame frequency. (stationary display with a stable number of "black bars" per frame scan). If you're still stumped when you've had a break and a recheck, could we have a look at the bit of circuit showing the line hold pot ? Pete PS Ah, I see you've progressed since I started typing ! What did you do ? Last edited by DangerMan; 15th Jul 2010 at 7:02 pm. Reason: Added PS |
15th Jul 2010, 7:06 pm | #93 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
changed the Sync separator
Post #89 is how it starts after locking, post #90 is after about 10mins. I'm going to turn on again in a mo and measure the EHT and A1 when locked, then when it's gone all moody |
15th Jul 2010, 7:21 pm | #94 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Ok turned on,
picture turns up locked and A1 is about 296. Picture becomes better as time passes and A1 rises to 301V EHT is 8.2KV after taking the photo the A1 reached 304.9V I'm monitoring to see what happens Edit: Dunno what happened in pic 4 but, went round to look at screen and it was sorted. monitoring continues.......... maybe it all goes pear shaped soon again. |
15th Jul 2010, 7:43 pm | #95 |
Dekatron
Join Date: Sep 2006
Location: Kilmarnock, Ayrshire, UK.
Posts: 5,420
|
Re: GEC BT1156 First Light & Vidor CN4216
Hi Chris.
From the ERT sheet the parts to check are, Line osc, c109 200pf, r65 330k, r69 100k, r112 1k. sync seperator c90 3.9pf, c89 100pf. you have low width so also check these, the width control adjustment L25/26 linearity L27 also r113 180k, on the osc c110 0.01uf, r117 3.9k c111 0.01, line o/p valve screen feed and decoupler, the boost cap. R114 680K G1 leak on the line o/p valve should be no more than 10% above value. Try these for starters.
__________________
Cheers, Trevor. MM0KJJ. RSGB, GQRP, WACRAL, K&LARC. Member |
15th Jul 2010, 7:45 pm | #96 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Ok still stable...............
Now I think I will perhaps by-pass the old metal rectifier with a IN4007 and 2x220R (parallel) in series and see if the HT is improved. |
15th Jul 2010, 7:50 pm | #97 |
Dekatron
Join Date: Sep 2006
Location: Kilmarnock, Ayrshire, UK.
Posts: 5,420
|
Re: GEC BT1156 First Light & Vidor CN4216
Chris.
In4007 is ok but 110 ohms as a limiter is way too high you need 22-47ohms but no higher you will land up wih less HT than you have now! Mind this is a telly not a radio that needs less current What is your present HT?
__________________
Cheers, Trevor. MM0KJJ. RSGB, GQRP, WACRAL, K&LARC. Member Last edited by murphyv310; 15th Jul 2010 at 7:52 pm. Reason: added question |
15th Jul 2010, 7:52 pm | #98 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Hi Trevor not talking about a limiter, I already have replaced the orginal duff EHT limiter which was a 5.1R (as per schematic) nearest I had was a 4.7R
I'm talking about the forward voltage resistor required when putting in a IN4007 |
15th Jul 2010, 7:55 pm | #99 |
Dekatron
Join Date: Sep 2006
Location: Kilmarnock, Ayrshire, UK.
Posts: 5,420
|
Re: GEC BT1156 First Light & Vidor CN4216
The correct terminology for the resistor in series with the IN4007 is a Surge Limiter, it does exactly as it says, so 22-47 ohms as I have said.
The 5.1 ohm you refer to is not an EHT limiter its only reduces the voltage to the EHT rectifiers heater, so they dont glow like a light bulb!
__________________
Cheers, Trevor. MM0KJJ. RSGB, GQRP, WACRAL, K&LARC. Member Last edited by murphyv310; 15th Jul 2010 at 7:58 pm. Reason: Added Line |
15th Jul 2010, 7:59 pm | #100 |
Retired Dormant Member
Join Date: Nov 2009
Location: Weardale, UK.
Posts: 1,981
|
Re: GEC BT1156 First Light & Vidor CN4216
Here's a pic of the EY51 tidied up Solder cups, and new resistor on the base of the EY51, I forgot to post this.
Before and after pics Sorry Trevor was only repeating what I had heard & seen others call the in series resistor with silicon rectifiers and it's value, at least now I know better, thanks Chris Edit: Well it's been almost 1 hour and the testcard is stable and bright. Last edited by oldticktock; 15th Jul 2010 at 8:16 pm. |