UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > Specific Vintage Equipment > Vintage Test Gear and Workshop Equipment

Notices

Vintage Test Gear and Workshop Equipment For discussions about vintage test gear and workshop equipment such as coil winders.

Reply
 
Thread Tools
Old 18th May 2018, 9:57 am   #1
nigelr2000
Heptode
 
nigelr2000's Avatar
 
Join Date: Nov 2008
Location: North Walsham, Norfolk, UK.
Posts: 607
Default Taylor 45c Valve Tester

I acquired this tester from another member and it appears to be working nicely bar a couple of small problems, it is the one with 17 positions and a 3 way switch on the "C" switch and has the 2 extra valve bases for B10B valves and big B9D base.
According to the book the hand written entry for PL509 reads that I set it to A4 B7 C16 with 60/60 anode and screen and 40 volt heater. Now I have several PL509's a couple new in box but can get no Mutual conductance readings on any of them. Also it seems to read other valves I have tested and compared with my mates tester fine on Mu. but I can't get a gas test again you can hardly get the meter to move so my questions are :-
1. is that the right settings for PL509

2. why is the gas test not working, being a newer one the book with it states 1980 modifications fitted, the circuit for it is a poor photocopy so difficult to follow.

Anyone know of a link to a decent copy for the 1980 modified circuits?
nigelr2000 is offline   Reply With Quote
Old 18th May 2018, 3:43 pm   #2
Freya
Octode
 
Freya's Avatar
 
Join Date: Jan 2009
Location: Falmouth, Cornwall, UK.
Posts: 1,378
Default Re: Taylor 45c Valve Tester

So far as I know these were not made or modified after the Avo acquisition of Taylor so my assumption would be that it has been modified by a third party.
Is the poor schematic that you have specifically related to the modifications or just handwritten extras in the Mods list. There are a couple of testers floating about that have an additional 3 position switch connected to the "C" range to give extra positions, I vaguely remember it was for B9D and B10B.
The gas test directly uses the same circuit as for the Mutual conductance so if one isn't working then its related to the other.
__________________
Stephen
________________________

"It`s only an old telly"
Freya is offline   Reply With Quote
Old 20th May 2018, 7:01 pm   #3
Craig Sawyers
Octode
 
Craig Sawyers's Avatar
 
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 1,202
Default Re: Taylor 45c Valve Tester

I've been trying to remember how my 45C actually works. Setting up for a non-listed valve is - well a bit challenging.

But in the end I reckon that the settings for a PL509, assuming that it fitted to the B9A base with heater on pins 4 and 5, is

A6 B12 C16

I don't have a PL509 to validate those settings, but have a look and see what you think.

Craig
Craig Sawyers is offline   Reply With Quote
Old 21st May 2018, 10:36 am   #4
David Simpson
Octode
 
Join Date: Mar 2008
Location: Aberdeen, UK.
Posts: 1,477
Default Re: Taylor 45c Valve Tester

Folks, 60V on the Anode & Screen of a PL5** hardly draws any Ia. Therefore getting a mA/V reading will be difficult on a Taylor45. I seem to remember that this problem with 45's was raised a year or two back & discussed at length.

Regards, David
David Simpson is offline   Reply With Quote
Reply

Thread Tools



All times are GMT +1. The time now is 7:31 am.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright ©2002 - 2018, Paul Stenning.