UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > General Vintage Technology > Hints, Tips and Solutions (Do NOT post requests for help here)

Notices

Hints, Tips and Solutions (Do NOT post requests for help here) If you have any useful general hints and tips for vintage technology repair and restoration, please share them here. PLEASE DO NOT POST REQUESTS FOR HELP HERE!

Reply
 
Thread Tools
Old 28th Jul 2020, 7:06 am   #1
FrankB
Hexode
 
Join Date: Oct 2005
Location: Olympia, Washington, USA.
Posts: 468
Default Stuck Ferrite IF cores.

We all have run into this from time to time.
I ran into a lot of this in TV servicing and old radios.

That "delightful" hex hole core was stuck. Often from hot glue, or more commonly beeswax or silicone seal.

Getting a stuck core out can try the patients of a Doctor (LOL).

I found sometimes pouring some denatured alcohol into the core would loosen it, but more often digging out the silicone seal, or hot glue- and heating the coil carefully with a heat gun to melt the bees wax out.
Sometimes putting in a nail filed to the core shape and heated would loosen the beeswax quite quickly too.

Then comes that sound we all dread... Crunch! When the core breaks into a pile of ferrite pieces.
I learned decades ago that this was way more common than I liked. So I started removing the adjustable ferrite cores from old TV and radio chassis, 2 way radios, etc.
I would carry a box of them of assorted diameters and lengths in my service kit. (GC- General Cement, used to make a kit of assorted replacement cores).

The core you need too long? File it down or use sand paper to reduce the length. Too short? Put 2 cores snug with each other, and cement together with ferrite cement. Then put in the coil form.

Now I never found any problem with ferrite mix causing a problem in the coils. Sometimes I'd have to adjust the core to a different spot to get the correct adjustment, due to the replacement core being a bit longer, shorter, etc; but it never failed me.

Oh, and carry a few VERY thin rubber bands in your kit too. Some cores used a thin strip of rubber band to "lock" the core in place. No glue, silicone, or beeswax needed. I did carry a small ball of bees wax to seat the cores with and wax dial cords too.

The very last thing I wanted to do was replace a good coil with a replacement just because of a broken core.
FrankB is offline   Reply With Quote
Old 28th Jul 2020, 8:54 am   #2
SeanStevens
Heptode
 
SeanStevens's Avatar
 
Join Date: Sep 2009
Location: Bath, Somerset, UK.
Posts: 875
Default Re: Stuck Ferrite IF cores.

I have a transistor radio that needs 3 or 4 cores replaced. They are not broken yet, but will be if I try any harder to get them out.

Does anybody sell slug replacement sets still?

SEAN
__________________
There are only 10 types of people, those who understand the binary system, and those who don't.
SeanStevens is offline   Reply With Quote
Old 29th Jul 2020, 2:06 pm   #3
Tractionist
Heptode
 
Join Date: Apr 2016
Location: Cheltenham, Gloucestershire, UK.
Posts: 663
Default Re: Stuck Ferrite IF cores.

Some people also recommend eardrops [i.e. those intended to dissolve and/or dislodge wax] .........? Hear! Hear!
__________________
Red to red, black to black. Throw the switch and stand well back!
Tractionist is offline   Reply With Quote
Reply

Thread Tools



All times are GMT +1. The time now is 5:43 am.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Copyright ©2002 - 2020, Paul Stenning.