|
Vintage Audio (record players, hi-fi etc) Amplifiers, speakers, gramophones and other audio equipment. |
|
Thread Tools |
16th Nov 2018, 4:58 pm | #1 |
Retired Dormant Member
Join Date: Mar 2017
Location: Wiltshire, UK.
Posts: 9
|
Dynatron HFC2A Radiogram.
I have an old Dynatron radiogram and the left speaker output isn't working properly so I'm after a bit of friendly advice. I'm as sure as I can be that the large cylindrical TCC Lectropack capacitor, which is a 2000uF 18v DC TCB/XH 0266, has failed.
I can't find an original replacement, and the capacitors I can find online do not come in the same values. The closest I can get is 2200uF and 25v. Would that be a suitable replacement ? There is one capacitor for the left speaker, one for the right speaker - the right seems to be working fine, but should I replace both so they are the same ? |
16th Nov 2018, 5:24 pm | #2 |
Moderator
Join Date: Jun 2003
Location: Oxford, UK
Posts: 27,966
|
Re: Replacing Capacitor
That will be a suitable replacement, but you shouldn't change it without a good reason. Swapping caps is a poor fault finding strategy. There are many possible causes of these symptoms, and a bad output coupling cap isn't even the most likely (though it's possible of course).
Why do you think it is bad? |
16th Nov 2018, 6:29 pm | #3 |
Retired Dormant Member
Join Date: Mar 2017
Location: Wiltshire, UK.
Posts: 9
|
Re: Replacing Capacitor
Thanks, I'm the first to admit that electronics aren't my strong point, but I'd like to learn. The reason for suspecting the capacitor is that I did a bit of testing with my multimeter and found that I got an output for the right speaker, none for the left (both speakers themselves work fine, it's the left output from the radiogram that does not work). So I tested the resistance over the resistor on each speaker output and got same values, so then tested the earths for the speaker sockets - all good. I then tested the positive wires from the speaker sockets to the capacitor (all OK), and positive wires from the capacitor to the next connection (not sure what it is, but call it X) - all OK. I then tested the speaker socket positive to the point X and the right speaker was fine, nothing on the left. So as the capacitor and the resistor are the only components between the socket and X, and the resistors show the same readings but the right socket is showing a reading and the left isn't, my simple brain reckoned it was probably the capacitor ? I only have a multimeter, no fancy measuring equipment. What do you think ? Is there a proper test I can do (with just a multimeter) ?
|
16th Nov 2018, 6:37 pm | #4 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,289
|
Re: Replacing Capacitor
Do you have a model number so we can find a circuit and guide you from there?
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
16th Nov 2018, 6:49 pm | #5 |
Retired Dormant Member
Join Date: Mar 2017
Location: Wiltshire, UK.
Posts: 9
|
Re: Replacing Capacitor
Yes, that would help wouldn't it - sorry ! Its difficult to read but I think its HFC2A - late 60's I think.
|
16th Nov 2018, 7:17 pm | #6 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,289
|
Re: Replacing Capacitor
Here's an extract from the circuit.
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
16th Nov 2018, 7:39 pm | #7 |
Octode
Join Date: Jun 2006
Location: St Osyth, Nr Clacton, Essex, UK.
Posts: 1,482
|
Re: Replacing Capacitor
With that electrolytic disconnected you can do some simple tests on it just using your multimeter. As a start, discharge the cap by shorting its wires/legs together. Then set your multimeter to resistance and put the probes on the cap legs. The meter (is it analogue or digital?) should give a low resistance reading at first and then over a second or two (depending on the capacitance etc) the reading should increase until it stabilises at some high resistance reading (ideally infinite). Switching to voltage, you should see the voltage that the meter has charged the cap up to and that should slowly (very slowly for a DMM) decrease as the meter's internal resistance discharges the cap.
This is all easier with an analogue meter as changing digits can be hard to see. If you felt like repeating this for the known-good cap you could compare readings. This only works for capacitors in the multi-uF range, like yours. Graham
__________________
Half my stuff is junk - trouble is, I don't know which half! |
16th Nov 2018, 8:20 pm | #8 |
Banned
Join Date: Dec 2013
Location: Middlewich, Cheshire, UK. & Winter in the Philippines.
Posts: 3,897
|
Re: Replacing Capacitor
You could swap the capacitors from one channel to the other.
|
16th Nov 2018, 8:22 pm | #9 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,289
|
Re: Replacing Capacitor
Perhaps, with reference to the circuit diagram, the OP could tell us where he's taking the readings which differ between channels and what the readings are including units.
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
16th Nov 2018, 8:56 pm | #10 |
Dekatron
Join Date: Aug 2013
Location: Wigan, Greater Manchester, UK.
Posts: 9,433
|
Re: Replacing Capacitor
Possible but that risks two duff channels.
__________________
Frank |
16th Nov 2018, 9:21 pm | #11 |
Banned
Join Date: Dec 2013
Location: Middlewich, Cheshire, UK. & Winter in the Philippines.
Posts: 3,897
|
Re: Replacing Capacitor
Why?
One good capacitor should work in either channel. The bad one, if it is bad, won't work in either. Or are you suggesting that a fault in the output transistors could destroy the capacitor? |
16th Nov 2018, 9:25 pm | #12 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 14,007
|
Re: Replacing Capacitor
|
16th Nov 2018, 9:31 pm | #13 |
Banned
Join Date: Dec 2013
Location: Middlewich, Cheshire, UK. & Winter in the Philippines.
Posts: 3,897
|
Re: Replacing Capacitor
Fine if Biffo has spares to hand......................
Just trying to be helpful, hat and coat on, I'm gone.......... Last edited by Boater Sam; 16th Nov 2018 at 9:32 pm. Reason: correction |
16th Nov 2018, 9:37 pm | #14 |
Dekatron
Join Date: Aug 2013
Location: Wigan, Greater Manchester, UK.
Posts: 9,433
|
Re: Replacing Capacitor
Hi Sam,
I am of the school if it’s not broke don’t fix it school. It’s possible that the capacitor could break the good channel but more likely just working on an old PCB if there is no need can introduce faults. Perhaps I am over cautious but the poster admits to having little expertise and therefore may cause more problems. If the old cap is being removed, may as well just replace it with new, better still do some fault finding.
__________________
Frank |
16th Nov 2018, 11:03 pm | #15 |
Heptode
Join Date: Jan 2009
Location: West Lothian, UK.
Posts: 762
|
Re: Replacing Capacitor
If you have any capacitor in your junk box over about 100uF and 18v or more then just clip it across the suspect to see if any audio comes through.
__________________
George |
17th Nov 2018, 11:50 am | #16 |
Retired Dormant Member
Join Date: Mar 2017
Location: Wiltshire, UK.
Posts: 9
|
Re: Replacing Capacitor
Thanks for all the help and suggestions, and the diagram. I'm struggling to align the circuit diagram to the "contents" of the radiogram though. Where are the left and right speaker outputs ? I assume C22 and C25 are 2000uF capacitors ? It might be easier if I take some pictures and post them up later today.
|
17th Nov 2018, 1:08 pm | #17 |
Rest in Peace
Join Date: Sep 2008
Location: Solihull, West Midlands, UK.
Posts: 4,872
|
Re: Replacing Capacitor
Making sure that it is the right way round.
Yes, no sound may mean that the output coupling capacitor has gone open circuit so temporarily paralleling it with a good cap will check for this. |
17th Nov 2018, 1:12 pm | #18 | |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,289
|
Re: Replacing Capacitor
Quote:
The diagram only shows the LH channel. The RH channel will be exactly the same, but the component designations may be different. The capacitor you're referring to is probably C22. Have you checked the 1 amp fuse?
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
|
17th Nov 2018, 6:57 pm | #19 |
Retired Dormant Member
Join Date: Mar 2017
Location: Wiltshire, UK.
Posts: 9
|
Re: Dynatron HFC2A Radiogram.
Thanks, the fuse does sound an obvious thing to check - I'm struggling to identify it in the equipment though. Here are some photos:
https://www.vintage-radio.net/forum/...1&d=1542477127 Are the fuses visible in any of them ? My money is on the things in the last picture, but I'm used to car fuses, not sure what I'm looking for here ? I just connected my multimeter (digital) over the capacitor I thought was at fault (the one at the top in pic 1, out of its holder), and the resistance gradually increases to 0.93. I did the same over the other capacitor (still in its holder top right in pic 3) and it gradually increased to 0.76. That makes me think the capacitor is probably OK ? |
17th Nov 2018, 7:04 pm | #20 |
Dekatron
Join Date: Apr 2011
Location: Cornwall, UK.
Posts: 13,454
|
Re: Dynatron HFC2A Radiogram.
Third photo, top left, red and yellow wires, the fuses should be on the other side of the chassis at that point, the ones you think might have been fuses are transistors.
Lawrence. |