UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio and TV Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > Specific Vintage Equipment > Other Vintage Household Electrical or Electromechanical Items

Notices

Other Vintage Household Electrical or Electromechanical Items For discussions about other vintage (over 25 years old) electrical and electromechanical household items. See the sticky thread for details.

Closed Thread
 
Thread Tools
Old 27th Dec 2020, 12:14 am   #1
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default DC motor rewind help ?

Good Evening.

How difficult is it to figure how to rewind a DC permnant magnet motor?

This isn't a giant, it's off a treadmill, rated at 180v DC and 1.25 Hp. The windings are pretty burnt up but intact. I have tried to find out around the 'net but it doesn't yielded the right information, so I am looking for advice from someone who has done it before.
Thanks
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 27th Dec 2020, 1:02 am   #2
Radio Wrangler
Moderator
 
Radio Wrangler's Avatar
 
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,799
Default Re: DC motor rewind help ?

You may find that the armature windings are welded, not soldered to the com segs. This is for heat rather than cost.

David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done
Radio Wrangler is online now  
Old 27th Dec 2020, 5:03 pm   #3
Graham G3ZVT
Dekatron
 
Graham G3ZVT's Avatar
 
Join Date: May 2010
Location: Greater Manchester, UK.
Posts: 18,675
Default Re: DC motor rewind help ?

I suppose I was lucky with my "skip find" treadmill, I was sure I was going to have to replace the seized-up motor and I had priced up a replacement at £50 including postage, but when I dismantled it I found that although the windings had overheated, they were undamaged and some resin had leached out into the gap and needed carefully dressing away with a file.
Attached Thumbnails
Click image for larger version

Name:	motor.jpg
Views:	220
Size:	163.3 KB
ID:	223252   Click image for larger version

Name:	armature.jpg
Views:	233
Size:	127.4 KB
ID:	223253  
__________________
--
Graham.
G3ZVT
Graham G3ZVT is offline  
Old 27th Dec 2020, 6:29 pm   #4
Guest
Guest
 
Posts: n/a
Default Re: DC motor rewind help ?

I might be a bit OT but why a treadmill, I have a perfectly good pavement outside my house and it has changing scenery. "Green" too, no electric needed.
 
Old 27th Dec 2020, 6:32 pm   #5
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

Quote:
a replacement at £50
Thanks David and Graham.
An absolute giveaway price. This one starts at £140 + (on eBay). It actually looks like the same armature, certainly seems wound the same. Mine has that crispy blackened look with shiny bare copper shining through. Bad news the comm segs appear to be welded, so crimp and solder are out of the question I suppose?
I would like this thread to run a little longer, longer the the treadmill anyway and see if anyone has tackled one before.
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 27th Dec 2020, 6:35 pm   #6
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

Quote:
Originally Posted by merlinmaxwell View Post
I might be a bit OT but why a treadmill, I have a perfectly good pavement outside my house and it has changing scenery. "Green" too, no electric needed.
It's for a rather agile and athletic young lady and she rather dislikes displaying her >>assets<< in the street
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 27th Dec 2020, 7:32 pm   #7
Guest
Guest
 
Posts: n/a
Default Re: DC motor rewind help ?

Quote:
and she rather dislikes displaying her >>assets<< in the street
I see, sometimes when I wake in the early hours and can't get back to sleep I go for a night walk. SHMBO likes it because when I get back I have a lovely quiet sleep.
 
Old 27th Dec 2020, 9:47 pm   #8
Radio Wrangler
Moderator
 
Radio Wrangler's Avatar
 
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,799
Default Re: DC motor rewind help ?

It strikes me as fundamentally wrong that these treadmills require energy input from the mains. Shouldn't a good exercise machine be doing something useful like charging batteries?

David.
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done
Radio Wrangler is online now  
Old 27th Dec 2020, 10:37 pm   #9
mark_in_manc
Octode
 
Join Date: Nov 2011
Location: Manchester, UK.
Posts: 1,872
Default Re: DC motor rewind help ?

Quote:
Originally Posted by merlinmaxwell View Post
I see, sometimes when I wake in the early hours and can't get back to sleep I go for a night walk.
For one frightening moment I thought we were still going with the 'displaying one's assets in the street' angle

I bought a dead treadmill from ebay for the motor (small machine tool project). If you're lucky you may find the same model listed cheap with a scruffy case or dead control board. Also like bread machines and juicers, they seem to be the kind of thing folks buy and then sell on, not having used them that much!
__________________
"The best dBs, come in 3s" - Woody Brown
mark_in_manc is offline  
Old 28th Dec 2020, 12:29 am   #10
McMurdo
Dekatron
 
McMurdo's Avatar
 
Join Date: Jun 2009
Location: Staffordshire Moorlands, UK.
Posts: 5,263
Default Re: DC motor rewind help ?

dont these normally have to be dynamically balanced after a rewind? They tend to run rather fast.
You also need to take precautions when dismantling a PM motor as far as weakening the field magnets is concerned. You need to make a keeper.

I'd be tempted to look for new one, these chinese treadmill parts are usually pretty cheap.
For example someone sent me in a speed controller blown up and the new board (I think it was a Reebok branded chinese machine) was about £18
__________________
Kevin
McMurdo is offline  
Old 28th Dec 2020, 12:49 am   #11
Lucien Nunes
Rest in Peace
 
Join Date: Apr 2008
Location: London, UK.
Posts: 2,508
Default Re: DC motor rewind help ?

It's not particularly difficult but slow and error-prone until you have had some practice. I don't think rewinding a small armature that is available off the shelf is worthwhile unless you are doing it mainly for your own interest. I've done various motor and generator repairs and have never been tempted despite being at least reasonably well equipped to do it. OTOH this size and rating of motor should be fairly forgiving as the wire is robust and easy to handle, and the turns few in number, so it's as good a place to start as any. The only thing you won't be able to do is to dynamically balance the finished job. As Kevin says that might be a noticeable problem given the running speed and the domestic application. In locales where wages are low and goods are relatively more expensive, you can get power tools rewound in roadside shacks by guys working with little more than a hammer and a screwdriver. They don't seem to worry about balancing, but then the aim is simply to get a working tool rather than one working to original spec.

You might be able to change the comm for one with hook-type risers for a couple of quid, in which case you have more options for termination. HMP solder might do as there's more heat dissipation surface and it's further from the bars. Riserless comms are cheaper and ideal for automated winding and assembly, hence used in original production.
Lucien Nunes is offline  
Old 28th Dec 2020, 10:37 am   #12
crackle
Rest in Peace
 
Join Date: Mar 2011
Location: Basildon, Essex, UK.
Posts: 4,100
Default Re: DC motor rewind help ?

I am one for having a stab at fixing something, but I would definitely not bother even attempting a rewind on a motor like that. For the reasons stated, reliable termination of the windings, and final balancing of the armature for rotation at high speed.

Mike
crackle is offline  
Old 28th Dec 2020, 4:04 pm   #13
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

It appears to me now that treadmill motors are a rather hard-done-to item, from the dead one in front of me it appears that cooling has been almost overlooked. This motor does have a small fan on the end of it to draw air through the motor,, the air inlet holes being rather small and clogged up with dust. Bad design all around.

This particular treadmill is a "Re***k" high ender, over £1000, any reason why they didn't use an AC/DC motor and Triac speed control ?
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 28th Dec 2020, 4:22 pm   #14
Radio Wrangler
Moderator
 
Radio Wrangler's Avatar
 
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,799
Default Re: DC motor rewind help ?

I've had a look at a couple of dead treadmills and both were problems with the microcontroller. One of them used a thyristor bridge as a rectifier to power a DC motor.

Maybe they want the low speed torque because of the stiction of the belt? The motor will have its worst cooling problem at low speeds, so a fan on its own shaft is useless. A small blower unit as a separately powered unit is needed.

I guess a brushed DC motor is cheaper than a three phase motor with an inverter.

So, it takes 1.5 horsepower to overcome the belt friction to allow the runner to get some exercise... Words like 'inefficient' don't do it justice. I prefer a definitive 1 horsepower exerciser that doesn't need fossil fuels. You can even get a decent bicycle for less than £1000, but it won't be branded R**b*k.

To get a reliable machine will be much more expensive, and would have to be from a specialist manufacturer where the extra money goes to extra engineering, not extra brand marketing. An engineering high-ender.

David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done
Radio Wrangler is online now  
Old 20th Jan 2021, 2:02 pm   #15
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

Refreshing this thread. I have the armature in front of me, the commutator segments are just bent over. Using domestic oven I have picked off some of the >glue< and can see a lot better now.

The windings would be easy to get off IF they weren't glued together with the wire enamel? So far I have tried MEK, Benzl alcohol based paint stripper, acetone, meths and isopropl to try and remove the ?enamel?.

Italian made motor , I want to rewind it for my own interest now. Any suggestions would be welcome.
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 20th Jan 2021, 2:28 pm   #16
ex 2 Base
Heptode
 
Join Date: Nov 2009
Location: Scarborough, North Yorkshire, UK.
Posts: 507
Default Re: DC motor rewind help ?

One of the problems with DIY rewinds, is finding a supplier of new copper wire in small quantities. So, keep all wire and weigh it, then add 10/25% as your bound to waste some. Try and remove the windings such, as to obtain the stepping of the slots and spacing of the com connections. Also, modern machine wound armtures don't use slotting, which as a hand winder you would need to protect the wire as you insert it into the slots, so space is a problem. Then there is varnish and stoveing before and after then balance. I notice that modern armature windings are not soldered to the com any more sort of crimp. Not so easy as it looks, I hope I haven't put you off. Ted
ex 2 Base is offline  
Old 20th Jan 2021, 2:52 pm   #17
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

Not at all Ted, I have studied up a bit in the last week. My problem is removing the old windings, modern paint strippers don't cut mustard, Nitromors USED to be good but the 'elf n safety killjoys took out the active ingredient (methylene chloride) and strippers containing it are unavailable :-(
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 20th Jan 2021, 3:01 pm   #18
Andrew B
Heptode
 
Andrew B's Avatar
 
Join Date: May 2015
Location: Bradford, West Yorkshire, UK.
Posts: 510
Default Re: DC motor rewind help ?

Ted and everyone, this is the enamel? I wish gone.
Attached Thumbnails
Click image for larger version

Name:	DSC03382.jpg
Views:	127
Size:	69.2 KB
ID:	224994   Click image for larger version

Name:	DSC03384.jpg
Views:	114
Size:	75.1 KB
ID:	224995  
__________________
worried about the electrons entering the circuit and the smoke leaving

Andrew
Andrew B is offline  
Old 20th Jan 2021, 5:36 pm   #19
Herald1360
Dekatron
 
Herald1360's Avatar
 
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,526
Default Re: DC motor rewind help ?

Quote:
Originally Posted by Andrew B View Post
Not at all Ted, I have studied up a bit in the last week. My problem is removing the old windings, modern paint strippers don't cut mustard, Nitromors USED to be good but the 'elf n safety killjoys took out the active ingredient (methylene chloride) and strippers containing it are unavailable :-(

Dichloromethane (methylene chloride) based strippers are still available (for industrial/professional use only). They're offered for sale on Ebay with various disclaimers and declaration requirements. Rather like full fat solder!
__________________
....__________
....|____||__|__\_____
.=.| _---\__|__|_---_|.
.........O..Chris....O
Herald1360 is online now  
Old 20th Jan 2021, 6:23 pm   #20
Lucien Nunes
Rest in Peace
 
Join Date: Apr 2008
Location: London, UK.
Posts: 2,508
Default Re: DC motor rewind help ?

The quick method, once you are completely happy that you have all the information other than the number of turns per coil, is to saw the coils off (or turn off in a lathe) close to the lams. The coil sides within the slots can be driven out from one end, possibly after cooking to loosen them. Then you can dissect a sample to count the turns.
Lucien Nunes is offline  
Closed Thread

Thread Tools



All times are GMT +1. The time now is 1:09 pm.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.