![]() |
![]() |
![]() |
|
Vintage Amateur and Military Radio Amateur/military receivers and transmitters, morse, and any other related vintage comms equipment. |
![]() |
|
Thread Tools |
![]() |
#1 |
Tetrode
Join Date: Mar 2011
Location: Western Isles of Scotland, UK.
Posts: 52
|
![]()
I have a pair of Eimac 3-500Z valves, boxed and look new, but is there any way
of testing them, short of installing them in an amplifier? Richard |
![]() |
![]() |
#2 |
Moderator
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,803
|
![]()
Not really, I'm afraid.
You need the full power supply capability to perform any meaningful test. Any decent amp ought to have sufficiently comprehensive metering to show how well the valves are doing Once you are applying these sorts of voltages you need serious enclosure to be safe, so you might as well have the full amplifier. 3-500Zs have a bit of a reputation for leaks and going gassy. David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done |
![]() |
![]() |
#3 |
Dekatron
Join Date: Sep 2007
Location: Oxfordshire, UK.
Posts: 4,310
|
![]()
I knocked together a test rig for some 304TLs once https://www.vintage-radio.net/forum/...ad.php?t=40860. I could measure emission and gm at 1200V but I really didn't want to go much higher than that in HT voltage given that there would have been hundreds of milliamps behind it with substantial energy stored in the psu caps. Unfortunately that rig was disassembled quite a while ago.
Cheers, GJ
__________________
http://www.ampregen.com |
![]() |
![]() |
#4 |
Tetrode
Join Date: Mar 2011
Location: Western Isles of Scotland, UK.
Posts: 52
|
![]()
Thank you.
I have a TL922 which is working well, and which I only use about once a week. The 2 valves are ''spares'', which I've had for some years, so I think it would be best to cross the replacement bridge when, and if, I ever need to. Yes? Richard |
![]() |
![]() |
#5 |
Dekatron
Join Date: Aug 2007
Location: W.Butterwick, near Doncaster UK.
Posts: 8,923
|
![]()
Yes indeed!
__________________
G8JET BVWS Archivist and Member V.M.A.R.S |
![]() |
![]() |
#6 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,953
|
![]()
Apart from death-by-internal-flashover the only way you can really kill these sorts of valves [apart from hitting them with a shovel] is by wearing-out or otherwise damaging the emissive cathode-current.
Any 'valve tester' therefore needs to be able to source/sink an Amp or so of HT! Not something easy to do in a consumer-grade valve-tester. When I used to do this stuff commercially I would regularly send a batch (that had done 1000/10,000 hours service in an amplifier) back to Eimac and ask them to run tests - then present the test-results to the client to show that "after 10,000 hours the valves are still within original production-specification, so we really don't need to be changing them...". This was great for me, since I could then sell the returned "Fully-Tested-by-Eimac" valves [along with the test certificates] to various radio-amateurs for their HF/VHF amplifiers. |
![]() |
![]() |
#7 | |
Pentode
Join Date: Jul 2009
Location: Roxburghshire, UK.
Posts: 196
|
![]() Quote:
Colin. |
|
![]() |
![]() |
#8 |
Pentode
Join Date: Oct 2005
Location: Hebden Bridge, West Yorkshire, UK.
Posts: 199
|
![]()
Hi,
Just to follow on from Colin's remarks - power valves may not take too kindly to long periods of no use. The cathode emission can suffer as can the gas seals. Normally they will recover quite quickly when put into service, though as Colin says there can be fireworks if the full heater voltage and full HT voltage are applied without warning. In a professional environment, it would be normal to rotate the spares with the working set - say once every 6/12 months - so that none have to experience an extended period of no power. There is the added benefit of knowing that the spares will actually work if called upon to do so in a fault repair situation. As you say that your spares have already been out of service for some years, then installing them in the linear and using a variac to bring the power up slowly is probably as good a test method as you're going to get. Once the power is at 100%, leave the rig on standby for 12 hours or so to make sure the cathodes are really properly heated, then apply CW drive to whatever the rated continuous power output is and leave the rig generating this output power into a dummy load for another 12 hours or so, to ensure them to reach their maximum operating temperature, which should take care of any gassiness. I realise you were looking for a test method which didn't involve installing them in the linear, but as others have said, at these power levels you need all of the protection afforded by the equipment which was designed for operation of them. cheers Peter G8BBZ
__________________
Peter G8BBZ |
![]() |
![]() |
#9 | |
Dekatron
Join Date: Nov 2006
Location: London, UK.
Posts: 3,496
|
![]() Quote:
I destroyed a wonderful Svetlana 572B - when I didn't know better, around 15 years ago. It was in an RF power application - one of my early Tesla coils. It survived a flashover, but I accidentally red-plated it and then then envelope started to kink and collapse. ![]() It was probably all over in a minute. I'm much, much, wiser and vastly more experienced now and always have belt and braces overcurrent protection circuitry. I have also studied, practiced and learned experientially about the efficiencies associated with different classes of amplifier and so can build in appropriate margin for anode dissipation.
__________________
Al |
|
![]() |
![]() |
#10 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,953
|
![]()
Not in my world: I designed valve-based 'stuff' such that it would run continually with no need for any maintenance or "tube-swapping". Some of my "stuff" regularly clocked 40,000 hours of service with zero downtime.
|
![]() |
![]() |
#11 |
Pentode
Join Date: Jul 2009
Location: Roxburghshire, UK.
Posts: 196
|
![]()
Not sure about the TL922 but if doing the variac thing, be sure to connect directly to the HT transformer bypassing any soft-start circuitry. Obviously run the heater transformer as normal. Two soft-starts in series can lead to other dramas in the PSU!
Also have a handful of HT fuses handy. If it does flash over before reaching the rated HT, run it for a few hours just below the flash-over voltage and it might recover, though you might have to repeat several times, and it might never recover quite enough. Given the price of these bottles, it's always worth a shot.. Cheers, Colin. |
![]() |
![]() |
#12 |
Tetrode
Join Date: Mar 2011
Location: Western Isles of Scotland, UK.
Posts: 52
|
![]()
Thank you for all the advice.
I am still rather nervous of this amplifier, especially when the meter is showing 3.2 kV, and wouldn't dream of running it with the lid off, especially with my level of experience! So I'll leave the 2 valves in their boxes for now! It may be possible in the future to have them professionally tested. Best wishes, Richard |
![]() |
![]() |
#13 | |
Moderator
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,803
|
![]() Quote:
Nowadays? David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done |
|
![]() |
![]() |
#14 |
Pentode
Join Date: Jul 2009
Location: Roxburghshire, UK.
Posts: 196
|
![]()
You shouldn't need to run it with the really nippy voltage parts exposed (the interlocks shouldn't let you) - and your lack of experience will make you careful!
Be sure to let the HT discharge before opening the lid and use an earthed chicken-stick to ground the anode supply before putting your hands in there to change the bottles. Colin mm1aps |
![]() |
![]() |
#15 | |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,953
|
![]() Quote:
And they still offer a "service report" analysis of used valves. And they still have their reference documents online: their "Care and feeding of Power Grid Tubes" in hardcopy was one of my go-to documents when building juicy amplifiers. See http://www.cpii.com/library.cfm/9 |
|
![]() |
![]() |
#16 |
Moderator
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,803
|
![]()
Interesting.
Wondered what had happened to them in all the shenanigans at the end of Varian as one group. Still have a copy of 'Care and feeding..." on my bookshelf. The best guide to beef thermionics up to UHF yet written. David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done |
![]() |