|
Hints, Tips and Solutions (Do NOT post requests for help here) If you have any useful general hints and tips for vintage technology repair and restoration, please share them here. PLEASE DO NOT POST REQUESTS FOR HELP HERE! |
|
Thread Tools |
3rd Nov 2018, 4:16 pm | #1 |
Heptode
Join Date: Jan 2009
Location: West Lothian, UK.
Posts: 761
|
Temporary load for power supply testing
Needed to test a 5 volt 20 amp power supply was working at full current and had no suitable resistive load. Google lead me eventually to a 3 minute youtube video:-
https://www.youtube.com/watch?v=WECW88rJYrE Using some scrap 0.7mm O/D (and some 0.4mm) enamelled copper wire I was able to dump the 20 amps and later 35 amps as a test of a transformer.
__________________
George |
3rd Nov 2018, 6:41 pm | #2 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,535
|
Re: Temporary load for power supply testing
Somewhat more sophisticated is a length of stainless steel thin wall tube between a couple of hoses with water flow through. Electrical connections can be via big crocodile clips or a bit better, worm drive hose clips.
Don't forget to turn on the water..... hoses blowing off red hot tube in a cloud of steam is a bit lairy 5l/min water and 60C rise is good for 20kW.
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O |
4th Nov 2018, 4:57 am | #3 |
Banned
Join Date: Feb 2018
Location: Horncastle, Lincolnshire, UK.
Posts: 203
|
Re: Temporary load for power supply testing
In a similar vein I needed a high wattage resisistor for the current sense input of a 723 based PSU I'm homebrewing. I needed 2 ohms, in the end I used part of an old electric fire element. I just bolted a wire to one end then used a hose clip with a wire attached and slid it up and down the bar until I got the resistance I needed. It works perfectly, also heat proof and easy to mount.
|
4th Nov 2018, 5:34 pm | #4 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,998
|
Re: Temporary load for power supply testing
Cunning!
In the past I've used a coil of galvanised-steel agricultural fencing-wire to make a 48VDC dummy-load; dunk it in a (plastic) bucket of water and it can dissipate a few hundred Watts for quite a long time (I ran it overnight and only a bit of the water boiled away). Old car headlamp bulbs are also good - I get H4 (main/dip beam) bulbs with one dead filament for free from my local friendly garage. Wire a bunch of these in series/parallel and you can easily get to 500 Watts dissipation. |
4th Nov 2018, 5:51 pm | #5 |
Dekatron
Join Date: Jun 2015
Location: Biggin Hill, London, UK.
Posts: 5,208
|
Re: Temporary load for power supply testing
6V car bulbs (not easy to find, but they do exist) make good dummy loads for 5V power supplies. I've used 1 or 2 6V headlamp bulbs with the fillaments in parallel as a dummy load on a minicomputer PSU I was rebuilding.
|
4th Nov 2018, 7:49 pm | #6 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,998
|
Re: Temporary load for power supply testing
6V bulbs persisted a lot longer in the world of motorcycles.
|
4th Nov 2018, 11:10 pm | #7 |
Octode
Join Date: Nov 2013
Location: Penrith, Cumbria, UK
Posts: 1,993
|
Re: Temporary load for power supply testing
Still very much available.
https://www.mandp.co.uk/motorcycle-s.../standard.html Probably even halfords too but you'll need to order them these days. A. |
6th Nov 2018, 2:58 pm | #8 |
Nonode
Join Date: Mar 2010
Location: Dukinfield, Cheshire, UK.
Posts: 2,037
|
Re: Temporary load for power supply testing
I use the same method. And they light up when 'on' which is always handy.
__________________
Andy G1HBE. |
7th Nov 2018, 6:40 pm | #9 |
Hexode
Join Date: Jan 2012
Location: Weymouth, Dorset, UK.
Posts: 422
|
Re: Temporary load for power supply testing
One bit of advice I'd give if you're using lamps as a load is it's a good idea to have them switched so you can bring them on one or two at a time because the inrush current might make the PSU shut down because the cold current is many times greater than the hot current. Just an extra precaution worth taking especially with some picky SMPSUs.
|