|
Homebrew Equipment A place to show, design and discuss the weird and wonderful electronic creations from the hands of individual members. |
|
Thread Tools |
22nd Oct 2019, 11:35 pm | #1 |
Octode
Join Date: Feb 2018
Location: Southampton, Hampshire, UK.
Posts: 1,051
|
DIY 18VDC power supply for Hacker Sovereign II
Here is an 18V DC power supply I put together in an old Philips battery eliminator case. I did not have to change the transformer, which was 18-0-18V. I was also lucky to find a cord from another old wall wart with the exact slim DC plug that fits perfectly in the recessed Hacker DC socket. The heatsink hardly gets warm after over an hour over constant use. I've screwed back the cover of the eliminator. A perfect fit with functionality.
|
23rd Oct 2019, 1:48 am | #2 |
Octode
Join Date: Sep 2017
Location: Bristol, UK.
Posts: 1,642
|
Re: DIY18V DC power supply for Hacker Sovereign II
That's neat! Do you get any zero-volume mains hum on the Hacker? They do seem to be quite sensitive to it (and I suppose with a PA input sensitivity of 50mV, they are entitled to be!). My RP25A has some from it's VP408, but I suppose with 50-year-old components, I need to check a few of them.
Mike |
23rd Oct 2019, 8:54 am | #3 |
Octode
Join Date: Feb 2018
Location: Southampton, Hampshire, UK.
Posts: 1,051
|
Re: DIY18V DC power supply for Hacker Sovereign II
Thanks Mike. I have no hum on FM, MW and LW using my circuit. I also ran the radio from another DIY power supply using an LM317 and there is no hum either. I have seen pictures of the VP408 but am not sure what might be causing the hum. If it is difficult to repair, making a supply similar to mine is inexpensive and easy. The main expense would be the transformer and housing, unless you are able to use your existing one. In addition to the Philips transformer and housing, I used a PCB from an old surge protector and the DC cord with the correct plug cut off an old wall wart.
|
24th Oct 2019, 8:38 am | #4 |
Octode
Join Date: Sep 2017
Location: Bristol, UK.
Posts: 1,642
|
Re: DIY18V DC power supply for Hacker Sovereign II
Thanks for that. I probably wasn't very clear - I should have said that the hum I mention is very low level - just about audible in a quiet room and slightly less than you'd expect from an old valve receiver in good nick - so very low. But I wouldn't expect even that low level from a solid-state receiver and amplifier with regulated PS. As I said, the electronics is very old (original circuit-board transferred from 50-year-old VP408), so maybe should check some components. The Hacker is far from being useless with the slight hum, but still we must strive for perfection...!
Mike Last edited by Boulevardier; 24th Oct 2019 at 8:46 am. |
24th Oct 2019, 9:00 am | #5 |
Dekatron
Join Date: Sep 2003
Location: Near Swindon, North Wiltshire, UK.
Posts: 3,595
|
Re: DIY18V DC power supply for Hacker Sovereign II
The Philips unit is an N6502, originally with three dc output voltages: 6, 7.5 and 9V @ 250mA max. The mains lead into it is pluggable and the "hard wired" dc output lead is terminated in a "Roka" plug, with an adaptor to convert it into a 5 pin (270 degree?)DIN plug, that was fitted on many Philips portable battery only cassette recorders.
It uses a typical series regulator circuit, with a zener diode voltage reference. Transistors AC128 and AD162. They are well made and seem to be widely available on auction sites, etc. |
26th Oct 2019, 1:02 am | #6 | |
Octode
Join Date: Feb 2018
Location: Southampton, Hampshire, UK.
Posts: 1,051
|
Re: DIY18V DC power supply for Hacker Sovereign II
Quote:
|
|
28th Oct 2019, 5:29 pm | #7 |
Dekatron
Join Date: Apr 2005
Location: North Wales, UK.
Posts: 6,884
|
Re: DIY18V DC power supply for Hacker Sovereign II
Don't forget these Philips transformers often had a thermal fuse inside that's easily resoldered, thank goodness, but often failed for no obvious reason. Just in case things go quiet unexpectedly...
|
28th Oct 2019, 6:47 pm | #8 |
Octode
Join Date: Feb 2018
Location: Southampton, Hampshire, UK.
Posts: 1,051
|
Re: DIY18V DC power supply for Hacker Sovereign II
Thanks Glyn. I'll bear that in mind.
|