|
Vintage Test Gear and Workshop Equipment For discussions about vintage test gear and workshop equipment such as coil winders. |
|
Thread Tools |
4th Jul 2017, 10:45 pm | #1 |
Dekatron
Join Date: Sep 2010
Location: Cheltenham, Gloucestershire, UK.
Posts: 3,077
|
Dremel 4000 Engraver
Can anyone offer advice or experience wrt the Dremel 4000, especially the external engraving tool option? I have had this Dremel 4000 for about a year but never used it. It was a freebie gift/reward via work and I've finally opened the box today because I want to try engraving some of my tools and equipment.
In the picture below you can see the Dremel 4000 and also my 'poor man's Dremel' that I bought from Maplin a very long time ago. It's the red drill in the red box in the back of the picture below. This is a crude but meaty 12V PCB drill that can also take rotary tools and it has served me well as a rotary grinder. But it's no good for serious/accurate engraving. So I finally have a need to play with the Dremel. I've watched a few Youtube videos that show the engraver in action but I don't know which tool is best to use for engraving and what the usual traps are. I know I have to wear proper safety goggles when using it but are there any gotchas with the external engraving tool accessory? I don't want to break it on the first day... Thanks in advance for any replies
__________________
Regards, Jeremy G0HZU |
4th Jul 2017, 11:04 pm | #2 |
Dekatron
Join Date: Feb 2003
Location: Cottingham, East Yorkshire, UK.
Posts: 5,766
|
Re: Dremel 4000 Engraver
I've got a Dremel 4000, which is the only model that goes down to 5,000RPM - most others and their 'clones' go from 10,000 - 30,000, which is too fast for some applications, certainly for the 15mm sanding arbors. I've never used it for engraving tools, and wouldn't personally do so as I think it's not a good application, the tool being rotary. Engravers aren't rotary, they're percussive, akin to a 'pneumatic drill, in that the tip doesn't rotate - it's a sharpened 'pencil point' tungsten carbide tip. They're not expensive and usually the impact of the strokes is adjustable dependant on the depth of engraving you desire. They often come with number and letter templates. EG:
https://www.cromwell.co.uk/shop/hand..._campaign=Hand Sorry if this seems a bit obtuse, rather like the guy who asked 'Can you give me directions to the railway station please?', and received the unhelpful answer: 'If I were you, I wouldn't have started from here'. (I have used my Dremel to cut holes and notches in glass meter dials using diamond burrs).
__________________
David. BVWS Member. G-QRP Club member 1339. |
4th Jul 2017, 11:33 pm | #3 |
Dekatron
Join Date: Sep 2010
Location: Cheltenham, Gloucestershire, UK.
Posts: 3,077
|
Re: Dremel 4000 Engraver
Thanks for the info about the alternative/better engraver. Maybe I'll go down that route instead if it's going to give better results for just £12. I had a look through the box of tools that came with the Dremel and there's not much there I think I would ever use. I bought a set of rotary tools with the Maplin drill many years ago and these are much smaller/finer and more suitable for the stuff I do. But they don't fit in the Dremel chuck!
There doesn't seem to be a fine engraving tool tip in the Dremel kit so I'm going to have to buy some suitable tool tips if I want to try using the engraver head. I'm not really that skilled at stuff like this but am willing to try a few experiments.
__________________
Regards, Jeremy G0HZU |
5th Jul 2017, 11:57 am | #4 | |
Octode
Join Date: Jan 2012
Location: Wimbledon, London, UK.
Posts: 1,465
|
Re: Dremel 4000 Engraver
Quote:
If I remember correctly, the softer the material, the slower the speed and the choice of tip will probably depend on the material being engraved and on the finished item. Why not try your hand with a few bits of scrap and work your way up - practice makes perfect. IIRC, my friend marks out what is to be engraved before picking up the engraving tool, especially on glass. His website is: http://www.thepewterscribe.co.uk/index.html If you tell him that "Pervy" gave you the contact, he might see you well, but I can't guarantee anything - it is his living, after all.. Colin. |
|
5th Jul 2017, 12:17 pm | #5 |
Pentode
Join Date: Jul 2015
Location: Newbury, Berkshire, UK.
Posts: 243
|
Re: Dremel 4000 Engraver
Wouldn't it be easier to electroengrave ? All you need is salt, water and current ... ?
|
5th Jul 2017, 1:11 pm | #6 |
Heptode
Join Date: Jul 2009
Location: Newcastle upon Tyne, Tyne & Wear, UK.
Posts: 723
|
Re: Dremel 4000 Engraver
Hi
If you mean that they don't fit the brass clutch thingy then look on ebay for a set of the brass bits, they come with loads of hole sizes. I can use any of the 3rd party burrs/drills/grinders/etc with my Dremel and the set of brass bits I have. Said it before but I love my Dremel 4000 - latest use is to open up and deepen the screwdriver slot in difficult bolt heads - then if the nut spins and I can't get at it to hold it - I just whip the head of the bolt off with a cutting wheel. Countersunk head? No problem with a burr tool! Nothing can stop me refurbishing this rusty kit now..... James Last edited by jamesinnewcastl; 5th Jul 2017 at 1:17 pm. |
5th Jul 2017, 1:24 pm | #7 |
Octode
Join Date: Jan 2012
Location: Wimbledon, London, UK.
Posts: 1,465
|
Re: Dremel 4000 Engraver
I agree with James and I was meaning to say that you can buy sets of collets for the Dremel chucks. Be careful, though, as some don't fit the nose of the Dremel properly. It is also worth bearing in mind that Dremel suggest that you only use approved (i.e. made by Dremel) accessories. I think the likelihood of one of those little grinding-wheels exploding is unlikely, but for the peace of mind it is probably worth shelling out the little bit more cash for approved kit. I have bought from Tyzack:
http://www.tyzacktools.com/default.aspx happily in the past (not associated, just a customer). I would also suggest that a full face-mask might be a useful thing to use - it isn't just your eyes that matter in your face. Colin. |
5th Jul 2017, 2:25 pm | #8 | |
Octode
Join Date: Jan 2012
Location: Wimbledon, London, UK.
Posts: 1,465
|
Re: Dremel 4000 Engraver
Quote:
Colin. |
|
5th Jul 2017, 5:20 pm | #9 | |||
Dekatron
Join Date: Sep 2010
Location: Cheltenham, Gloucestershire, UK.
Posts: 3,077
|
Re: Dremel 4000 Engraver
Thanks to all for the good advice...
Quote:
Quote:
Quote:
__________________
Regards, Jeremy G0HZU Last edited by G0HZU_JMR; 5th Jul 2017 at 5:29 pm. |
|||
5th Jul 2017, 6:28 pm | #10 |
Nonode
Join Date: Jan 2016
Location: Stafford, Staffs. UK.
Posts: 2,532
|
Re: Dremel 4000 Engraver
I once had a small grinding stone (5mm ish) leave the chuck of a rotary tool like this. I think it came loose in the chuck and as I tried to switch it off I instead increased the speed at which point the shaft started to bend and wobble much worse before exiting sharp right through a wine glass. Luckily it was an empty one!
|
5th Jul 2017, 6:51 pm | #11 |
Dekatron
Join Date: Jun 2015
Location: Biggin Hill, London, UK.
Posts: 5,222
|
Re: Dremel 4000 Engraver
I have the Dremel 4000 too, and I have learnt by bitter experience that the advice to use genuine Dremel accessories is sound. The cheap clones do not last. I've had cheap grinding points break up. Cheap cut-off disks shatter almost as soon as they start to cut, the Dremel one will get through quite a thick bar before it is worn away. I even managed (although it did take 2 of the cut-off disks to finish the job) to cut through a hardened steel bearing race that was rusted to a shaft.
The Dremel bits might be more expensive, but they are worth it I think. |
6th Jul 2017, 2:06 pm | #12 | |
Octode
Join Date: Jan 2012
Location: Wimbledon, London, UK.
Posts: 1,465
|
Re: Dremel 4000 Engraver
Quote:
https://www.safetysupplies.co.uk/tro...ace-shield.htm Maybe I should contact my engraver friend and ask his advice. I'll probably see him soon at the Great British Beer Festival at Olympia in August (overt plug - mods can delete if it is too overt). Colin |
|
12th Jul 2017, 2:07 pm | #13 |
Dekatron
Join Date: Jun 2009
Location: Staffordshire Moorlands, UK.
Posts: 5,274
|
Re: Dremel 4000 Engraver
Lidl do dremel-compatible bits from time to time, including engraving bits. I can't say they're much worse than the dremel originals; the cost of the latter makes every broken cutting disc painful in itself!
I wouldn't be without my dremel, its the sort of thing you find jobs for that you didnt realize were feasible. Safety-wise I use angle-grinding goggles and then if it's the sort of disc that is prone to shatter, I do it behind my desk magnifier as they do fly everywhere. The dremel handbook gives recommended speeds for the various bits and using the tool as intended only is the safe way. Great for cutting holes in plastic enclosures for IEC connectors, D-SUbs and oblong rocker switches, gaining access to potted modules & welded plastic boxes, trimming bolts, cutting nuts & rivets off, and generally making things fit. Cleaning solder-resist off pcb tracks. Polishing commutators, shortening pot shafts, re-facing contacts. The only thing I've not had success with is drilling holes.
__________________
Kevin |
12th Jul 2017, 2:44 pm | #14 |
Dekatron
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,864
|
Re: Dremel 4000 Engraver
Aldi are selling these for £9.99 as a grout remover.
https://www.aldi.co.uk/workzone-grou...76263147231100 However, I can confirm that they're IDENTICAL to the engraver David mentioned in post 2. N. |
12th Jul 2017, 4:16 pm | #15 | |
Octode
Join Date: Jan 2012
Location: Wimbledon, London, UK.
Posts: 1,465
|
Re: Dremel 4000 Engraver
Quote:
On a side-note, I hope that you don't use one of these in your professional activity.... OUCH!! Colin. |
|
12th Jul 2017, 4:22 pm | #16 |
Dekatron
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,864
|
Re: Dremel 4000 Engraver
Fair enough, Colin, I suspect you're right, but the appearance is uncanny and I suspect there's little difference fundamentally.
And no, I don't (obviously!). N. |
12th Jul 2017, 5:30 pm | #17 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,536
|
Re: Dremel 4000 Engraver
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O |
12th Jul 2017, 7:46 pm | #18 |
Dekatron
Join Date: Feb 2003
Location: Cottingham, East Yorkshire, UK.
Posts: 5,766
|
Re: Dremel 4000 Engraver
Interesting!
The fact that Dremel sell an engraving tool with a non rotational percussive action, in itself speaks volumes as in: "If you want a drill, buy a Dremel drill - if you want an engraver, buy a Dremel engraver". In the same way that Dremels have been marketed as a 'toolkit in a box', there's a parallel with WD40, which (allegedly) can be used for loosening seized screws and countless other applications, yet for some years now, WD40 have marketed a range of products for specific applications, such as electrical contact cleaner, and of course, penetrating oil. Id doesn't stop people buying WD40 and expecting it to loosen screws, not will the fact the Dremel sell and engraver stop people using Dremel drills to engrave, quite possibly with a measure of success. After all, there are those who use a hammer as a screwdriver, and a screwdriver to get the lid off a tin of paint! I'm not sure what tools glass engravers use, but some years ago for a 'special' birthday, a dear friend commissioned as a special present for me, a large straight-sided glass bowl which has a continuous village scene engraved all around it, with me on a motorbike. Very creative. It's not like painting a picture - there's no correcting any errors.
__________________
David. BVWS Member. G-QRP Club member 1339. |
12th Jul 2017, 8:10 pm | #19 |
Heptode
Join Date: Jun 2010
Location: Zurich, Switzerland
Posts: 538
|
Re: Dremel 4000 Engraver
David, maybe is your "picture" an etched one?
Karl |
12th Jul 2017, 8:52 pm | #20 | |
Dekatron
Join Date: Sep 2010
Location: Cheltenham, Gloucestershire, UK.
Posts: 3,077
|
Re: Dremel 4000 Engraver
Quote:
I've also used a CNC machine here at home (that uses a high speed rotary tool head) to mill/drill/rout PCBs and also used it to engrave logos into a PCB or front panel with good results. So this was what inspired me to experiment with the Dremel engraver accessory. I'm not looking to do anything deeply arty/crafty but the idea was to make a basic stencil of my name with the CNC machine and then use the Dremel engraver accessory to score out the letters. Hopefully, it would turn out reasonably straight with no slip marks etc
__________________
Regards, Jeremy G0HZU |
|