|
General Vintage Technology Discussions For general discussions about vintage radio and other vintage electronics etc. |
|
Thread Tools |
11th Jul 2019, 5:26 pm | #1 |
Octode
Join Date: Oct 2005
Location: Wimborne, Dorset, UK.
Posts: 1,407
|
American 60Hz clock - Will it run on pulsed DC?
Hi all,
Excuse me if I'm being ignorant here but I wanted your collective opinion, first I'll set the situation... I am currently looking at an american clock radio for somebody, it's made by Commodore and is a 117v valve set, now the 117v part isn't difficult as I have a suitable transformer that will fit inside the set as there is lots of room, the issue I do have though is with the clock itself as it runs way too slow on 50Hz Now, my question is this.. If I pulsed DC into the clock winding (also designed for 117vac) at 60Hz would it work? and secondly and most importantly could I do it with a much lower voltage? Answers on a postcard please!! Cheers
__________________
Lee |
11th Jul 2019, 7:15 pm | #2 |
Dekatron
Join Date: Dec 2007
Location: Haarlem, Netherlands
Posts: 4,203
|
Re: American 60Hz clock - Will it run on pulsed DC?
Pulsed DC seems like a bad idea. You could probably build a small sine generator and use it to drive a power transformer in reverse to obtain the right voltage.
|
11th Jul 2019, 9:00 pm | #3 |
Nonode
Join Date: Jan 2010
Location: North Somerset, UK.
Posts: 2,130
|
Re: American 60Hz clock - Will it run on pulsed DC?
Remember also that the inductive impedance of the clock motor winding will be reduced at a lower frequency.
You may therefore need to reduce the voltage to perhaps 100v/110 volts rather than the designed 117/120 volts. |
12th Jul 2019, 1:42 am | #4 |
No Longer a Member
Join Date: Oct 2016
Location: Maroochydore, Queensland, Australia.
Posts: 2,679
|
Re: American 60Hz clock - Will it run on pulsed DC?
You can order these with a UK input plug and get your 60Hz 110V power this way:
https://www.kccscientific.com/product/1930/ I have used other solutions too. Often the rotor in the clock is a separate item, available in both 50 and 60 Hz versions, if you are lucky you might find one in a clock on ebay. In one case for one of my 110V 60 Hz clocks, I disassembled the rotor assembly and Ken Reindel machined a new gear for me (near the output shaft) to alter the ratio to correct it for 50Hz use. He is a master clockmaker: http://www.kensclockclinic.com |
12th Jul 2019, 7:32 am | #5 |
Rest in Peace
Join Date: Apr 2011
Location: Matlock, Derbyshire, UK.
Posts: 1,378
|
Re: American 60Hz clock - Will it run on pulsed DC?
I have seen circuits of a 300Hz oscillator, phase locked to the mains and then this is divided by 5 to get 60Hz or 6 to get 50Hz. This will then need to be amplified to get a suitable supply for the clock.
Pulsed DC could work if the DC was blocked and only the pulses passed but you will need an accurate frequency source. There are invertor circuits to give out AC. This is a nice little project using CMOS or a microprocessor. |
12th Jul 2019, 8:02 am | #6 |
Dekatron
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,861
|
Re: American 60Hz clock - Will it run on pulsed DC?
Similar gadget to the one mentioned by Hugo here:
http://www.electric-clocks.co.uk/Fre...cyconvert.html |
12th Jul 2019, 8:10 am | #7 |
Pentode
Join Date: Jan 2008
Location: Derby, Derbyshire, UK.
Posts: 108
|
Re: American 60Hz clock - Will it run on pulsed DC?
I use one of these converters to run a 60Hz Telechron clock from 50Hz UK mains:
http://www.electric-clocks.co.uk/Fre...cyconvert.html |
12th Jul 2019, 8:58 am | #8 |
Dekatron
Join Date: May 2008
Location: Derby, UK.
Posts: 7,735
|
Re: American 60Hz clock - Will it run on pulsed DC?
There is no need to worry about the waveform, just as long as it is symmetrical (for the sake of the permanent-magnet armature). A crystal oscillator and suitable divider chain will do fine; the division should ensure symmetry. Use the Q and Q' outputs from your last flip-flop to drive the gates of a pair of MOSFETs, one drain to each end of the centre-tapped secondary winding of a suitable transformer, the tap to the unregulated supply and the primary to the clock motor.
Small transformers tend to have lousy regulation, so one rated for 18-0-18V from a 230V supply probably will give about the right output with a 12V DC supply. The clock should still run from a reduced voltage.
__________________
If I have seen further than others, it is because I was standing on a pile of failed experiments. |
12th Jul 2019, 9:34 am | #9 | |
Dekatron
Join Date: Sep 2005
Location: Seaford, East Sussex, UK.
Posts: 5,997
|
Re: American 60Hz clock - Will it run on pulsed DC?
Quote:
Quite complicated though. |
|
12th Jul 2019, 10:03 am | #10 |
Hexode
Join Date: May 2015
Location: Northampton, Northants, UK.
Posts: 380
|
Re: American 60Hz clock - Will it run on pulsed DC?
I would be inclined to use a microcontroller as a pseudo phase locked loop, one of the PICs with a zero crossing detector would be ideal.
|
12th Jul 2019, 10:44 am | #11 |
Dekatron
Join Date: Dec 2007
Location: Haarlem, Netherlands
Posts: 4,203
|
Re: American 60Hz clock - Will it run on pulsed DC?
When going the non-sinusoidal way, the RMS voltage would be important to get right, too.
|
12th Jul 2019, 11:06 am | #12 |
Hexode
Join Date: May 2015
Location: Northampton, Northants, UK.
Posts: 380
|
Re: American 60Hz clock - Will it run on pulsed DC?
Well, at a fixed, known frequency, a square wave can be made into a very good approximation of a sine wave (better than anything that comes off the mains, heh) with a simple RC filter. Then step it back up with a Class A or AB output stage... ooh, this is actually getting quite complicated isn't it?
|
12th Jul 2019, 3:30 pm | #13 | |
Guest
Posts: n/a
|
Re: American 60Hz clock - Will it run on pulsed DC?
Quote:
|
|
15th Jul 2019, 2:17 pm | #14 |
Octode
Join Date: Oct 2005
Location: Wimborne, Dorset, UK.
Posts: 1,407
|
Re: American 60Hz clock - Will it run on pulsed DC?
Hi guys,
Thanks for all the replies, I'm unsure yet which way to go regarding this, to buy a ready made unit or to construct from scratch (I prefer the latter I think) Still, plenty of food for thought. Thanks again! Cheers
__________________
Lee |