|
Components and Circuits For discussions about component types, alternatives and availability, circuit configurations and modifications etc. Discussions here should be of a general nature and not about specific sets. |
|
Thread Tools |
19th Dec 2011, 10:29 pm | #1 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
My first experience with electronic tubes
Hello everyone
I open this thread to ask for help (as ussual) about the misterious world (at least for me) of electronic tubes. I have always been “transistorised”, and I have a lot of experience using transistors. On th other hand, I have never use valves, despite the fact that when I began to experiment with electronics, there were a lot of valve-made equipment still in use in Cuba, such as Soviet-made TV sets and Chinese-made radio sets. For years, electronic tubes have been surrounded by a mystic curtain, covering them from my eyes. So, that was always a pending subject in my “career” as electronics lover In recent times I began to read about valves and their ussage. I read a good book from the 50s. Well, I proposed myself to build something with valves before I leave this world (I hope to be here for a long, long, long time, but I’d like to start now because tomorrow never knows) But I still have a huge lack of knowledge about this devices. The obvious equipment for a begginer should be an audio amplifier. I have search some diagrams and I have recolect some components, but I still have a lot of doubts. The diagram I pretend to implement is attached in this post. The doubts I have are the following: 1.) What should be the DC supply voltaje for this circuit.? (150, 200, 250, 300V) 2.) The first valve in that circuit is a Soviet-made 6Н2П (Dual triode). I don’t have that valve, instead I have several 6Н1П (Dual triode). May I replace in the circuit the 6Н2П by the 6Н1П, taking into account the pinout of each one? 3.) Valves circuit operates at high voltage. Should I electrically isolate the input terminals from the HV circuit in order to prevent electric shock in that points? 4.) Is there any risk for the source signal equipment (DVD player, CD player, Cassete recorder, radio, etc) to be affected by the high voltaje from the valved-circuit. I don’t want to burn out my CD player. 5.) Should I connect the negative terminal of the DC power supply to the chasis, and here I re-ask doubt #3 6.) The valves pinouts that appear in the datasheets are top-viewed (like ICs) or bottom-viewed. 7.) An explanation of the parameters that appear in the datasheets would be fine Sorry any silly question but as I said before I have a huge lack of knowledge in the electronic tubes world. You could check the 6Н2П & 6Н1П datasheets in the following link. Possibly you must use Google Translator: http://www.magictubes.ru/sprav/pdf/6n1p.pdf http://www.magictubes.ru/sprav/pdf/6n2p.pdf I do not pretend to build a super amplifier, but just a modest one to amplify my CD player and have fun while building it. I really don’t need it because I have a transistorised build by myself several tears ago, but as I said before it is a subject I have pending. Of course I will learn a lot about valves when I finish. Almost all valves that I have are Soviet-made, with some exceptions that are Czeck-made (TESLA). The output valve that I have is the 6П14П (EL84 equivalent). If anybody thinks that is not the best diagram for a beginner like me, feel free to tell me, and if posible recommend me another diagram. Remember that almost all components I have are used Soviet-made ones If I finally build this amplifier, maybe I will adapt to it an EM80 magic eye that I have, but that will be for the future, and for further learning. Any advise most welcomed Best regards Miguel |
19th Dec 2011, 10:36 pm | #2 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,192
|
Re: My first experience with electronic tubes
For forum members not familiar with Cyrillic script, the Cyrillic letter "П" is the same as the English letter "P"
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
19th Dec 2011, 10:40 pm | #3 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
Yep, you're right. And the Cyrillic letter "H" is actually the same as the "N" in English.
|
19th Dec 2011, 10:43 pm | #4 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,192
|
Re: My first experience with electronic tubes
Спасибо
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
19th Dec 2011, 10:48 pm | #5 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
You're welcome
PS: Hallowed be Google Translator |
20th Dec 2011, 1:39 am | #6 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,528
|
Re: My first experience with electronic tubes
The circuit looks to be a good simple class A amplifier to practice on.
As for the alternative double triode- even with google translate it's not easy to decide exactly what's going on, since it separates the text from the values in a rather unhelpful way. I would say, simply try it. It won't go bang- valves are quite robust electrically compared with transistors! Once it's running, you can check the various electrode voltages and adjust the anode and cathode resistors if necessary. Yes the negative side of the HT DC supply is connected to chassis- the circuit shows an isolating transformer, so there's no direct hazard from so doing, except for the HT voltage itself! You will not need to isolate the input of the amplifier from your CD player except if there's any DC coming from that- the grid circuit of the input valve is at 0V (chassis potential) and is inherently isolated from the HT voltage anyway. DON'T connect either side of the AC supply to chassis! You can connect the chassis itself to ground if you wish, for extra safety, though depending on the grounding arrangements in the signal source device this may cause hum problems. Treat the mains and HT with suitable respect and have some fun...... A few other answers: HT of 250V would seem reasonable, so you'll need a transformer secondary about 180-200V or so. Valve pinouts are viewed from underneath, so if you hold the 9-pin valve upside down with the gap in the pins towards you, you count 1-9 clockwise from the pin on the left of the gap. There are some odd other ways of counting on some of the older valve types, but anything made after about 1940 will conform.
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O Last edited by Herald1360; 20th Dec 2011 at 1:55 am. |
20th Dec 2011, 2:29 am | #7 |
Heptode
Join Date: Jul 2009
Location: Stoke-on-Trent, Staffordshire, UK.
Posts: 719
|
Re: My first experience with electronic tubes
очень не истинно, а т все
But your English is certainly better than Google's unedited translations, unless they have improved! However, I do still use it myself ! I would agree with earlier replies, by all means earth the HT-, but only if you have an isolating mains transformer. Best wishes Pete P.S. I will never understand "British" Industry.... At the time my (then) company won a very large Russian contract, I was the only person there who actually spoke Russian, but was was excluded from having anything to do with it !! I don't think it was in any way politically motivated... just bad management. |
21st Dec 2011, 3:05 pm | #8 | |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
Thanks Herald and Pete.
That answers make feel "more safe". In fact, the high voltage was always my first thought (and fear) everytime I interested myself in valves. But since I began to work with microwave ovens some months ago, I thought that 300V is nothing compared to 4kV, so why not? I have all the neccesary parts to begin to work with my valved-amplifier. Valves, transformers, capacitors, resistors, diodes.....all Soviet-made. But that's going to be for the next year, because we are now in Xmas and that's not a good time for electrocution......sorry, for work too much. But you have really cleared my doubts (and fears), thanks. Quote:
|
|
22nd Dec 2011, 5:56 pm | #9 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
I measured the TC-180 power transformer that I have, and I found that I can obtain 260 V DC to supply the amplifier. So, no problem on this .
And now I'm going to ask the 64000 dollars question (or pounds if you prefer). Is there any way to test the tubes before I start to "cut metal"? I only have two EL84. I hope that at least one of them be OK. But if none, I won't be so glad when I finish the job and I find that there is no EL84 to amplify the audio signal. Despite this, I think that I will build the amplifier anyway, because I have some other tubes (triodes mostly) and I could build a less powerful amplifier, but it would be better to use the EL84. Any idea? |
22nd Dec 2011, 9:35 pm | #10 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
Another tough question:
Is there any software to simulate an audio amplifier using valves? I always use "Electronics Workbench" to simulate my designs before implement them, but this software does not simulate electron tubes. |
23rd Dec 2011, 9:05 am | #11 | |
Nonode
Join Date: Oct 2008
Location: Warsaw, Poland and Cambridge, UK
Posts: 2,669
|
Re: My first experience with electronic tubes
Quote:
How's that? A valve tester using an HT power supply and one resistor. Chris |
|
23rd Dec 2011, 9:10 am | #12 |
Dekatron
Join Date: May 2008
Location: Derby, UK.
Posts: 7,735
|
Re: My first experience with electronic tubes
Most circuit simulation software is based on SPICE underneath, and therefore component models are more or less interchangeable. Someone's bound to have made a model for the EL84 -- they're common enough, after all.
__________________
If I have seen further than others, it is because I was standing on a pile of failed experiments. |
23rd Dec 2011, 12:00 pm | #13 |
Hexode
Join Date: Aug 2007
Location: S.W. London, UK.
Posts: 416
|
Re: My first experience with electronic tubes
There are Spice models available for many valves here. For simple circuits I'm with Chris, a quick lash-up on the bench is often faster and more informative than drawing and entering parameters in software where the model accuracy is unknown.
Vic
__________________
It has to be here... I've just put it down! |
26th Dec 2011, 6:40 pm | #14 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
I've read the EL84 datasheet. I found something that I do not understand. The minimal load resistance stated in that datasheet is:
Load Resistance ............................... 4.5K Ω The output transformer that I have has an ohmic resistance of about 230 ohms. Is that figure making reference to impedance instead of resistant?. |
26th Dec 2011, 6:44 pm | #15 |
Moderator
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,192
|
Re: My first experience with electronic tubes
Impedance and resistance are not the same thing. Resistance figures for transformer windings are only useful as a means of checking for shorted turns.
If your using say an 8 ohm speaker, the impedance ratio will be 4500/8 or 562.5 to 1. The turns ratio of the output transformer will need to be the square root of that or about 23 to 1.
__________________
Graham. Forum Moderator Reach for your meter before you reach for your soldering iron. |
26th Dec 2011, 8:20 pm | #16 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,528
|
Re: My first experience with electronic tubes
In the particular case of a resistive load on the secondary of a transformer, the primary will also look like a resistor (give or take imperfections inherent in any practical transformer), but only to ac signals and then only within the band of frequencies for which the transformer is designed. Hence the valve spec quoting a resistor value. You could indeed load the valve directly with a resistor, and it would be perfectly happy, but efficiency would be terrible with the large standing DC dissipation due to the anode current heating up the resistor, in addition to any desired ac heating effect.
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O |
26th Dec 2011, 8:52 pm | #17 |
Rest in Peace
Join Date: Sep 2008
Location: Solihull, West Midlands, UK.
Posts: 4,872
|
Re: My first experience with electronic tubes
Resistance is the real part of impedance, so the two terms can often be used interchangeably. In the case of a transformer, resistance may mean the DC resistance of a winding (or the loss resistance) or the real part of the reflected impedance. Impedance usually means the reflected impedance.
|
27th Dec 2011, 2:29 pm | #18 | ||||
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
Quote:
Quote:
Quote:
But I still do not understand the steady-state operation. When the circuit operates without signal (DC operation), the EL84 will only see the 230 ohms resistance od the primary winding. There is no power transfer in this state, but the anode DC current would be flowing throught this winding, producing warming due to Joule's effect. Quote:
|
||||
27th Dec 2011, 4:17 pm | #19 | |
Nonode
Join Date: Oct 2008
Location: Warsaw, Poland and Cambridge, UK
Posts: 2,669
|
Re: My first experience with electronic tubes
Quote:
Where power will be dissipated, though, is at the anode (and screen grid) of the valve. If the anode current is 40mA and the HT voltage 250V, then the anode will be dissipating 10 watts. That's OK because it's designed to do that. This current is limited not by the resistance of the transformer but by the characteristics of the valve. The impedance seen by the valve's anode only matters when the current starts to change - when an audio signal is present. If that impedance is too low, or too high, the valve won't be a good match to the load and so won't be able to develop its full output power. |
|
27th Dec 2011, 4:34 pm | #20 |
Heptode
Join Date: Dec 2011
Location: Mayabeque, Cuba
Posts: 617
|
Re: My first experience with electronic tubes
OK, I understand now. The fact is that I've never built a Class A amplifier, not even with transistors, so my huge in-experience on that matter added to my very, very huge in-experience with valves and then you'll understand why I'm asking such questions. Thanks for your answers.
Comparing the diagram I showed in the openning post of this thread with other similar configuration, I noticed two things: 1.) The resistor in the cathode of the output pentode is not bypassed by a capacitor. 2.) There is a 0,01uF capacitor (named C7) in the grid of the pentode, bypassing the resistor in that grid. I guess this would affect the high frecuency response What about this? |