|
Cabinet and Chassis Restoration and Refinishing For help with cabinet or chassis restoration (non-electrical), please leave a message here. |
|
Thread Tools |
12th Sep 2017, 9:10 pm | #21 | |
Nonode
Join Date: May 2007
Location: Preston, Lancashire, UK.
Posts: 2,511
|
Re: Re-anodising heatsinks?
Quote:
Andy |
|
13th Sep 2017, 7:13 am | #22 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
Didn't you see my earlier post regarding dissipation being almost all convection and hardly any through radiation for a temperature rise of less than 40C? The colour of the heatsink is pretty much irrelevant for a temperature rise of less than 100C.
There is another effect that reinforces this idea called the "view factor". Think about how much each part of a finned heatsink area sees of the environment, and is capable of thermally radiating. Before you get very deep into the profile, each area of the heatsink sees progressively less of the environment, and the more it sees of the adjacent fin. Since the adjacent fin is at the same temperature there can be no radiative energy transfer - it can only radiate if it sees a cooler environment which it can only peek through the gaps between the fins. All of which says: the colour of the heatsink does not matter if you can touch the heatsink without burning yourself. Cooling is close to 100% convection. The colour of a heatsink is traditionally black for decorative reasons only, and alas reinforces the pseudoscience argument that thermal radiation assists dissipation to a significant degree. Here is a link to a heatsink manufacturer that says the same thing http://www.abl-heatsinks.co.uk/heats...ace-colour.htm Quote "The heat transfer from the heatsink occurs by convection of the surrounding air, conduction through the air, and radiation. Heat transfer by radiation is a function of both the heat sink temperature, and the temperature of the surroundings that the heat sink is optically coupled with. When both of these temperatures are on the order of 0 °C to 100 °C, the contribution of radiation compared to convection is generally small, and this factor is often neglected. In this case, finned heat sinks operating in either natural-convection or forced-flow will not be effected significantly by surface emissivity." Craig Last edited by Craig Sawyers; 13th Sep 2017 at 7:41 am. |
13th Sep 2017, 7:42 am | #23 |
Nonode
Join Date: May 2007
Location: Preston, Lancashire, UK.
Posts: 2,511
|
Re: Re-anodising heatsinks?
OK Craig, I retreat defeated!
Andy |
13th Sep 2017, 8:04 am | #24 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
And from the Aavid heatsink manufacturer https://www.aavid.com/product-group/...ons-na/anodize
"Relatively large extrusions and those used at low temperature rise, as in many high power applications, will only gain up to 10% by the addition of an anodized surface. With forced ventilation (using a fan) convective cooling is about 3 times higher than in natural convection. This changes the proportion of heat transfer due to radiation. An anodized finish will only add 4 -8% to the overall cooling effect in forced air. This percentage again, depends on fin spacing and heat sink dimensions. The color of the anodized finish makes little impact on emissivity since most radiational heat loss occurs at wavelengths higher than visible light. As a thumb rule, if anodize is not required for aesthetic or corrosion protection, we suggest it only for small, open finned heat sinks in natural convection." Craig |
13th Sep 2017, 8:09 am | #25 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
Aplogies - my second post crossed with yours!
There is an application that needs 100% radiative cooling though - in space applications (where no-one can hear you scream!). Since it is in vacuum, the only method of getting heat out is via a radiator panel pointed at deep space (which is only about 2 Kelvin, so T1^4 - T2^4 is high). Each circuit board has a thermal layer connected to its housing. Each of those (there might be dozens or up to a hundred on a space vehicle) is coupled to the radiator panel with ammonia heatpipes. Craig |
13th Sep 2017, 8:28 am | #26 | |
Dekatron
Join Date: Apr 2009
Location: Oxfordshire, UK.
Posts: 4,935
|
Re: Re-anodising heatsinks?
Quote:
From what you say, it seems possible that painting something black could actually be detrimental from a thermal standpoint? Probably not a big effect, just a waste of time? B
__________________
Saturn V had 6 million pounds of fuel. It would take thirty thousand strong men to lift it an inch. |
|
13th Sep 2017, 8:54 am | #27 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
Well, back when I was involved in this from a production standpoint, anodising - particularly black - was a nightmare. Depending on the condition of the bath, and the repeatability of the dying and sealing processes you could get anything from a nice deep black right the way to almost a blueish tinted black.
What precise colour you get is also strongly dependent on the aluminium alloy - so that is another process to control if you aim to get colour uniformity. In the end we had a sample and the plater had a sample. They (it wasn't Metro Plating, by the way) were told that if the batch was visually different to the sample to strip it and replate. And we did rigorous QC on goods inwards. Powder coating can be much more predictable from a colour point of view, and with a much wider colour palette, but it is difficult to get uniform coating on sharp corners and into deep profiles (like a heatsink). There is another sneaky problem with extruded heatsinks - they are always slighly banana shaped. It is inherent in the extrusion process. Aavid cheerfully own up to that, and say if flatness of the device mounting surface is important (and why wouldn't it be?) that it should be post-machined flat. And they will do it for you - at an additional cost. Craig Last edited by Craig Sawyers; 13th Sep 2017 at 9:03 am. |
13th Sep 2017, 10:50 am | #28 |
Dekatron
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 14,007
|
Re: Re-anodising heatsinks?
It's not just space-in-a-vacuum that denies cooling by convection: anywhere in zero-gravity experiences the same effect. There are lots of fans used for cooling in things like the ISS.
[Zero-gravity has other odd effects: a friend of mine is NASA's fire-suppression-in-space supremo. Without convection, fire behaves very differently in zero-G !] |
13th Sep 2017, 2:21 pm | #29 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
That is a good point. My experience is with unmanned space vehicles - I hadn't thought of cooling implications in manned zero g environments, and particularly the hazards of fire and how it behaves.
|
13th Sep 2017, 5:11 pm | #30 | ||
Dekatron
Join Date: Feb 2007
Location: Lynton, N. Devon, UK.
Posts: 7,087
|
Re: Re-anodising heatsinks?
Quote:
I used to work for a well-known power supply manufacturer, their approach with large heatsinks for highly-dissipating linear power supplies was to black powder-coat the heatsinks! As far as I know, there was no study done to determine whether plain, black anodised, or black powder-coated were best. I suspect not very much difference, as others have commented! Last edited by kalee20; 13th Sep 2017 at 5:25 pm. Reason: clarification |
||
14th Sep 2017, 6:27 am | #31 |
Dekatron
Join Date: Jul 2009
Location: Sleaford, Lincs. UK.
Posts: 7,667
|
Re: Re-anodising heatsinks?
Old car engine oil is used in metalwork to give a black finish, the only problem is this is done by heating
said metal to cherry red. Easier to achieve with steel and iron than ali. Still might be worth experimenting with a blow torch. How big is said HS? To be honest I'd just spray it black with bog standard spray paint, doubt it'll ever get hot enough to damage the paint. Think of a car roof in summer, gets hopping on one leg waving your hand about hot. If that don't appeal here's - https://www.ebay.co.uk/sch/i.html?_f...paint&_sacat=0 various high temp paints as found on ebay. I've used both the barrel paint and SAS 59, works ok and have also used stove paint. Both the exhaust and stove paint comes off eventually, but then both hospital hot. I've had my burner glowing orange, not blacking can survive that. Andy.
__________________
Curiosity hasn't killed this cat...so far. |
14th Sep 2017, 7:59 am | #32 |
Moderator
Join Date: Mar 2012
Location: Fife, Scotland, UK.
Posts: 22,899
|
Re: Re-anodising heatsinks?
There's also a guy in Sweden who takes aluminium electrolytic capacitors, de-cans them and re-homes the innards in little hardwood housings. His web pages are quite lyrical about the improvements to be obtained and the effects of different woods. No mention of life-expectancy. I'm afraid I didn't bother to save the URL when I was pointed to it.
Couldn't be the same bloke, could it? I suppose he'd have gone for Iroko heatsinks. At least the gold plate will have virtually no effect in either direction. David
__________________
Can't afford the volcanic island yet, but the plans for my monorail and the goons' uniforms are done |
14th Sep 2017, 8:46 am | #33 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,536
|
Re: Re-anodising heatsinks?
Would the recased electrolytics be any worse than old cardboard cased ones?
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O |
14th Sep 2017, 10:40 am | #34 | |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
Quote:
No - the guy I know's day job is at the Karolinska Institute carrying out research aiming at helping stroke patients recover more quickly and better by Transcranial Direct Current Stimulation. His degree is in engineering Physics with majors in mathematics and computer science. So a hard technologist - not a smoke and mirrors guy by any stretch Craig |
|
14th Sep 2017, 11:00 pm | #35 |
Banned
Join Date: Jun 2015
Location: Mareeba, North Queensland, Australia
Posts: 2,704
|
Re: Re-anodising heatsinks?
That guy in sweden should rehouse some 3-1000A's in wooden cases!!!
The sound should be superb, especially in class A Joe |
15th Sep 2017, 7:22 pm | #36 | |
Pentode
Join Date: Aug 2005
Location: Shrewsbury, Shropshire, UK.
Posts: 149
|
Re: Re-anodising heatsinks?
Quote:
As seems to be usual on this forum, I learned a great deal about heatsinks and heat transfer from this thread and many thanks to all for the very valuable suggestions. Every day's a schoolday |
|
15th Sep 2017, 8:08 pm | #37 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
I'd be interested in who the company in Manchester is
|
16th Sep 2017, 12:08 am | #38 |
Dekatron
Join Date: Feb 2007
Location: Lynton, N. Devon, UK.
Posts: 7,087
|
Re: Re-anodising heatsinks?
Yes - please share! (With a photo of the refurbished heatsinks!)
|
16th Sep 2017, 8:55 am | #39 |
Pentode
Join Date: Aug 2005
Location: Shrewsbury, Shropshire, UK.
Posts: 149
|
Re: Re-anodising heatsinks?
The company is Colour Anodising of Radcliffe, Manchester. I'll put up before-and-after pics of the results as soon as they return
|
16th Sep 2017, 11:19 am | #40 |
Dekatron
Join Date: Nov 2010
Location: Oxford, UK.
Posts: 4,991
|
Re: Re-anodising heatsinks?
I did a web search before you posted, found them, and discounted them - because the website looked so swish I was sure they had to be expensive!
But very interesting looking company. Regarding gold plating, I also had a look around the UK and found http://www.goldplating1.co.uk/ in Bolton. Prices look really good - maybe I'll try a heatsink and see what they would quote for stripping and gold plating. |