UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio and TV Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > Other Discussions > Homebrew Equipment

Notices

Homebrew Equipment A place to show, design and discuss the weird and wonderful electronic creations from the hands of individual members.

Closed Thread
 
Thread Tools
Old 28th Sep 2019, 5:54 pm   #1
Wendymott
Octode
 
Wendymott's Avatar
 
Join Date: Jun 2013
Location: Huddersfield, West Yorkshire, UK.
Posts: 1,782
Default PCB saw revisited.

Hi Peeps... I thought you may be interested in my revised PCB Material saw.

Building the one featured in this forum, I was quite disappointed with its performance, mainly it was under powered and too small for my needs.

I increased the bed size to 300 mm in length, and ordered a new motor from Ebay... this is a 12/24V DC motor capable of 10,000 rpm.. it states "Large Torque.. but no figures.. However it was approx 25% larger than the original motor, so I thought.. big is better. The shaft size was increased from 3 mm to 5 mm. AND... it cost £5.89 inc postage.
When I returned from my "jollies", I set to and upgraded the saw. I had to increase the vertical clearance by 5mm, so I added spacers to the end mountings rather than making new ones..
The motor plate needed replacing though... not enough metal to mount the motor face.
I Made a new saw mandrel to cope with the new 5mm shaft and fitted a shake proof washer to stop it coming undone..however the rotation of the motor is important.. the wrong rotation and a right handed thread will unscrew... thus I changed the start end to furthest away from me.. cutting towards me.
I had already fitted a saw guard as suggested by Argus..and I was fortunate to buy a LED lamp which fits very neatly onto the motor plate.
I needed better illumination as it was difficult to see the edge of the blade.
It still needs a PSU, however at present its not an urgent problem as the saw will only be used infrequently, and I have sufficient bench supplies.
The photo's show... quick and dirty...a means to an end... not an end in its self.
I am not decrying the previous articles, its just that in my circumstance it was just not up to my requirements.
I hope this may be of use to other members.
Attached Thumbnails
Click image for larger version

Name:	SAW 1.jpg
Views:	239
Size:	42.5 KB
ID:	190991   Click image for larger version

Name:	SAW 2.jpg
Views:	232
Size:	31.6 KB
ID:	190992   Click image for larger version

Name:	SAW 3.jpg
Views:	219
Size:	51.8 KB
ID:	190993   Click image for larger version

Name:	SAW 4.jpg
Views:	201
Size:	51.6 KB
ID:	190994  
__________________
Should get out more.

Regards
Wendy G8BZY
Wendymott is offline  
Old 29th Sep 2019, 3:52 am   #2
M3VUV51
Banned
 
Join Date: Feb 2018
Location: Horncastle, Lincolnshire, UK.
Posts: 203
Default Re: PCB saw revisited.

i use a bench grinder with some madrels to fit a 5inch x 1mm angle grinder thin metal cutting blade,cuts fingers as well as pcb material!!
M3VUV51 is offline  
Old 2nd Oct 2019, 9:47 am   #3
crackle
Rest in Peace
 
Join Date: Mar 2011
Location: Basildon, Essex, UK.
Posts: 4,100
Default Re: PCB saw revisited.

Dont you just reverse the motor connections to reverse direction of rotation.

Mike
crackle is offline  
Old 2nd Oct 2019, 10:56 am   #4
Wendymott
Octode
 
Wendymott's Avatar
 
Join Date: Jun 2013
Location: Huddersfield, West Yorkshire, UK.
Posts: 1,782
Default Re: PCB saw revisited.

Hi Crackle.. Yes thats what you do.. but then the face of "attack" is changed.. thus you saw away from you.
__________________
Should get out more.

Regards
Wendy G8BZY
Wendymott is offline  
Closed Thread

Thread Tools



All times are GMT +1. The time now is 6:41 pm.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.