|
Vintage Test Gear and Workshop Equipment For discussions about vintage test gear and workshop equipment such as coil winders. |
|
Thread Tools |
11th Oct 2013, 11:03 am | #1 |
Octode
Join Date: Feb 2007
Location: Ely, Cambridgeshire, UK.
Posts: 1,976
|
Kingshill model 15A03c
Looking for service info please. Control PCB marked KHD 125-SS issue 1 7/84
Have no output, not too complicated, but circuit would make life easier 0 to 150 volt 0 to 300mA |
11th Oct 2013, 12:03 pm | #2 |
Octode
Join Date: Feb 2007
Location: Ely, Cambridgeshire, UK.
Posts: 1,976
|
Re: Kingshill model 15A03c
Pictures if they help.
|
11th Oct 2013, 12:34 pm | #3 |
Dekatron
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,536
|
Re: Kingshill model 15A03c
No idea if this will be any help, but the unit looks similar to yours.
__________________
....__________ ....|____||__|__\_____ .=.| _---\__|__|_---_|. .........O..Chris....O |
11th Oct 2013, 12:46 pm | #4 |
Octode
Join Date: Feb 2007
Location: Ely, Cambridgeshire, UK.
Posts: 1,976
|
Re: Kingshill model 15A03c
Yes, somewhat the same. May help. Pity there is no parts list, but certainly a help.
Cheers. |
11th Oct 2013, 2:39 pm | #5 |
Octode
Join Date: Feb 2007
Location: Ely, Cambridgeshire, UK.
Posts: 1,976
|
Re: Kingshill model 15A03c
Also found early version of V series without op amp but includes parts list. Between the two should help me more.
|
25th Oct 2013, 8:01 am | #6 |
Octode
Join Date: Feb 2007
Location: Ely, Cambridgeshire, UK.
Posts: 1,976
|
Re: Kingshill model 15A03c
Mine is now fixed using the circuit uploaded by Herald1360
As there was no parts list I have made a part one from my unit Version 15A03 With PCB marked KHD 125-SS issue 1 7/84 VT3/4/5 BC108 VT8 BCY70 I USED 2N2907A VT9 BFY51 MR1 1N4005 MR2 BRIDGE OF 4 1N4005 MR3 9V1 MR4 1N823 (6.2V) MR5 9V1 MR6 3V3 MR7 1N4003 MR10 1N4003 MR9 5V1 MR11 1N4003 MR12 IS MADE OF 3 ZENERS IN SERIES 1 X 43V 1N5367 AND 2 X56V 1N5370 ALL 5W 0A1 OP AMP 741 RV2 50K POT VOLTAGE O/P COURSE RV3 1K POT VOLTAGE O/P FINE C4/8/9 10n 250V DC C11 100n 250V DC C7 100p 630V DC C3 4u7 160V C1 150u 63V I USED 220u C6 100u 10V In mine the zeners MR12 had scorched the PCB but measured ok I replaced all 3 also MR4 /R12 47 ohms /RV3 /VT8 and the 3 electrolytics C1/3/6 |