Re: The "Sussex" Homebrew Valve Tester.
2 Attachment(s)
Some more photographs show the wiring.
|
Re: The "Sussex" Homebrew Valve Tester.
2 Attachment(s)
I've been asked by Martin "G8UWM-MildMartin" to add some notes to the 'Bill of Material', it's now at version 12.
The reason for the updating the ‘Bill of Material’ was the original design by the late Mike Rowe, there was update (see the last paragraph). Lets call the original Version One, there are two further design versions a Four and a Nine, these updates are thanks to Martin “Dekatron”. The original consisted of three boards, Main, Daughter and Low Voltage Heater. Version Four only one PCB board was used and two Power MOSFETs are used to supply voltage to the Anode and Screen grid switches. Also linear voltage regulators are used to obtain the low heater voltages. Version Nine, a daughter board (LR8 board) is mounted on main PCB which removes the series Zener Diodes, ie ZD1...ZD7 arrangement and uses a high-voltage, low-output current adjustable linear regulator (U1). to control two Power MOSFETs (TR2 & TR4) for the Anode and Screen grid voltages. The schematic diagram has TR2 & 4 as IRF830, but the BOM (Post #974) captured by “Herald1360” on a post #104 before it disappeared has them listed as BUZ80, theses are not available at Farnell but STP3NK80Z are. Which are rated at 800 volts at 2.5A, this explains why they run cool, requiring no heat sink. Mike G4WYZ 29/10/2018 NB The picture is competed Sussex. |
Re: The "Sussex" Homebrew Valve Tester.
Hi!
For those who want or need to test series–operated valves in TVs or universal radios, etc., the traditional method of catering for these on valve–testers has always been to use multitudes of selecor switches and transformer secondary taps, etc., etc., which, in the 40s/50s was the only reasonable way of dealing with these types of valve, but as other Members have pounted out, rapidly makes expanding the "Sussex" to deal with series–operated valves a no–go in the traditional methods! Now that economical semiconductors/modules are available it's time fo look at this problem afresh! If you consider these valves again, the maker always stated "Sîeries Supply" for the heaters in their data, so instead of having to try and guess myriads of heater–voltages that might range from 3.6V to over 60V (leaving out such gems as the 117L7/117N7 for now!), we provide a simple high–voltage current controlled supply, with a simple selector switch in the current regulator giving currents of 100, 150, 200 and 300mA, with a simple Asian High Voltage Boost Voltage Converter Module, feeding a floating 7805 connected in Constant–Current Mode, with four resistors to select the current output. A fourth 0–200V meter can then be added across the heater terminals to monitor the valve's heater voltage, and this test is also suitable for testing for partial s/c's across CRT heaters! Circuit Information and parts list to follow when I've bought the module and tested it! Chris Williams |
Re: The "Sussex" Homebrew Valve Tester.
Quote:
Thanks. |
Re: The "Sussex" Homebrew Valve Tester.
Hi!
Further to my above post earlier today I have now chosen two inexpensive modules, currently about £10 total, that will (hopefully!) provide a simple economical series-heaters valve expansion for the Sussex Valve Tester suitable for 100mA, 150mA, 200mA, and 300mA valves. Only one simple 12V isolated supply is needed, I'll provide exact details, drawings and specs when I've tested the circuit - the modules have to come from China! (I know you've got "X" and 'L' series valves if you really do want to push the boat out but the number of times I've come across a 450mA or a 600mA valve in my lifetime is nil!) Chris Williams |
Re: The "Sussex" Homebrew Valve Tester.
Hi!
The Sussex Construction & Operating Manual states "Ed Dinning can manufacture transformers with an additional 6V winding for a fourth meter on request" and I ordered mine with this in mind, but for any Mamber who only had a standard three–meter transformer made, then a 3W dc–dc isolated converter module rated for 9 or 12V dc output can be connected to the Sussex's positive LT supply for the control circuits or rectified (W01 bridge and 1000u 25V) from one of the low voltage heater supply windings to power a fourth meter – these converters are rated 1kV isolation so the meter module's supply requirements are correctly catered for! Chris Williams |
Re: The "Sussex" Homebrew Valve Tester.
Hi!
Just a quickie update to say if any Member finds the short bit of wire supplied with the connectors on the Sussex's specified LCD Meter Modules is too short to be of any use, you can find these in cheapie Far Eastern audio products or old VCRs, or, if you don't have any of these items, IS possible to purchase the connector contacts and housings separately or in small bags of kits from Far East/Chinese online vendors – they're called 'XH' series connectors, and you can buy them from 2–way to 8–way! Chris Williams |
Re: The "Sussex" Homebrew Valve Tester.
Quote:
I brought mine from Farnell and their part no is 722431 73's Mike |
Re: The "Sussex" Homebrew Valve Tester.
Hello Mike G4WYZ,
When you were suggesting an alternative MOSFET you wrote - 'Which are rated at 800 volts at 2.5A, this explains why they run cool, requiring no heat sink.' They will only run cool if they are passing a small current or dropping a small voltage. If you test an EF86 at 4mA at 250V they will run cool. If someone tries to test a power valve at low voltage and high current, the MOSFET in the anode regulated supply will get hot. It will need a heatsink. |
Re: The "Sussex" Homebrew Valve Tester.
Thank you for pointing this out, the only valves I've tested is small signal types and 7360's as I only built mine for that application.
|
Re: The "Sussex" Homebrew Valve Tester.
Hello, I'm new to the world of forums so apologies if you have been here before. I am very interested in building the Sussex Valve Tester and it appears pcbs and transformers are still available, how do I order these please?
Also have there been notes on construction or is it a case of work it out from the schematic. Many thanks for help with this. |
Re: The "Sussex" Homebrew Valve Tester.
Hi, this was a very successful tester design and I believe numbers in the 100's must have been built.
I believe the manual can be downloaded from this site and one of the contributors can also supply the PCB's, but these are being used up quickly. Switches and the meter modules are available on the web. I can supply the transformer. Go for it! Ed |
Re: The "Sussex" Homebrew Valve Tester.
Quote:
|
Re: The "Sussex" Homebrew Valve Tester.
Quote:
Rgds Richard |
Re: The "Sussex" Homebrew Valve Tester.
I sold out of PCBs 6 months ago.
I've had three other requests since, so I'll order another batch this week for the winter construction season. |
Re: The "Sussex" Homebrew Valve Tester.
Hi Martin, that’s great!
One of the positives of Sweden is we have a proper ‘winter construction season’ :-) |
Re: The "Sussex" Homebrew Valve Tester.
Hi folks, transformers are still available if required, but are wound to order these days so delivery is about 3 weeks.
Cheers Ed |
Re: The "Sussex" Homebrew Valve Tester.
Hi Ed,
Please could I order a transformer from you? Regards, Peter, G0GPH |
Re: The "Sussex" Homebrew Valve Tester.
Hi Martin,
Please could you add me to the list if you are making some more pcbs? Thanks. Peter, G0GPH |
Re: The "Sussex" Homebrew Valve Tester.
Hi Peter, you have a PM
Ed |
All times are GMT +1. The time now is 3:50 am. |
Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.