Valve equivalents - electrically
 

There are loads of valve equivalent lists around, i.e. different numbers for either the exact same thing or something close.

I have noticed people making comments like XXXX valve was effectively the same as the old YYYY valve but in a modern envelope.

But does anyone know of lists of valves that are not plug-compatible but are effectively the same thing?

As much older valves become scarce, it would be useful to know that one can substitute it using a particular "modern" valve using a suitable adapter.

Are there also lists of the exact same valve but with a different heater? Sometimes this is easy to guess - but not always.

Re: Valve eqivalents - electrically
 

Id be interested to know this, but I suspect it comes down to studying data sheets with a few valves in mind.

I'm lazy and often just look for drop in replacements, and for that I use the rtype web site which shows list of "sensible equivalents", then take a look on ebay or whatever...

Re: Valve equivalents - electrically
 

It's an interesting question: you get things like the EL41 and UL41 which you'd _think_ were the same innards with different heater-voltages, but the published figures don't necessarily bear this out.

There are also oddities - I've seen a version of the 6V6 with a 300mA heater rather than the usual 450mA - it was apparently used in some US TV sets.

Re: Valve equivalents - electrically
 

EF6 - EF36 - EF37 - EF37A - EF40 - EF86 is the near exact equivalent series that spring to mind for me.

EF50 - EF91 - EF80 are pretty similar.

No doubt there are others.

Re: Valve equivalents - electrically
 

Hello,
The tube search section from radiomuseum.org https://www.radiomuseum.org/dsp_searchtubes.cfm
gives quite a lot of information such as different base, different heater voltage etc.
For example :- https://www.radiomuseum.org/tubes/tube_6k7g.html
Yours, Richard

Re: Valve equivalents - electrically
 

There were some intriguing notes on substitutions in the original volume of the 'Mullard Maintenance Manual' for certain obsolete types. Some were verging on 'desperate' and would state 'change base/xx resistor/heater volts' and the like ( sometimes more than one ! ) no doubt to keep a set going at any cost.
There was indeed a '12V6' as I have some RCA samples.

Andy

Re: Valve equivalents - electrically
 

A book was published during the war with a view to keeping sets working even if only on the local station.
Valve Replacement Manual For Radio Service Engineers Hardcover – 1 Jan. 1941
by A.C. And Arthur Woffenden Farnell (Author)
Doesn't seem available in the UK at the moment but worth looking out for.
https://www.amazon.co.uk/Valve-Repla.../dp/B001OZRSQY

Re: Valve equivalents - electrically
 

I have that book - 2nd edition 1943...It was my Dad`s.

Never found it that useful to be honest but I always had plenty of other data books available.

Re: Valve equivalents - electrically
 

This discussion has prompted me to mention the long-obsolete Philco-badged PenDD61 , one of which I found last week whilst clearing some space in my less-than-pretty shed . Sadly , a basic test showed a very low gm !
It was actually a Mazda AC/2PenDD , but with a 6.3v. heater to match the American valves in a U.K. built set. It was said to be a "concession" to the B.V.A.
Or has someone been pulling my leg ?

Re: Valve equivalents - electrically
 

In reality most valves used in domestic run of the mill applications will work given the right number of electrodes and about the same anode power rating and bias conditions (only really important for output jobs). The ECC85 used in VHF/FM sets is a bit of an exception, pushed to the limit is an understatement!

Re: Valve equivalents - electrically
 

Many circuits will accept anything - but that is only like with transistors, where same basic kind is enough - because the circuit didn't rely on the exact parameters.

But as mentioned, some next generation valves were effectively the same electrodes mounted a different way. That should give a very close match.

I was hoping to find tables of this.

Re: Valve equivalents - electrically
 

Radiomuseum's valve info provides some details of similar valves with different base/heater/envelope shape etc.

eg:

https://www.radiomuseum.org/tubes/tube_75.html

Re: Valve equivalents - electrically
 

Maybe this is what you are looking for: https://frank.pocnet.net/vademecum0.html

Re: Valve equivalents - electrically
 

Brimar had the “Brimaraze” marketing information for valve substitution for obsolete or unobtainable valves. This from the Brimar manual no 7, they also had adverts with suggestions in WW.