UK Vintage Radio Repair and Restoration Discussion Forum

UK Vintage Radio Repair and Restoration Discussion Forum (https://www.vintage-radio.net/forum/index.php)
-   Cabinet and Chassis Restoration and Refinishing (https://www.vintage-radio.net/forum/forumdisplay.php?f=21)
-   -   Repainting my Leaks TL12 plus! Came out pretty good! (https://www.vintage-radio.net/forum/showthread.php?t=146544)

vishalk 15th May 2018 9:39 am

Repainting my Leaks TL12 plus! Came out pretty good!
 
3 Attachment(s)
So I wanted to share with you my successful attempt at refurbishing my lovely Leaks, they needed some TLC and I wanted to get them back to looking good again.

I bought these in this condition, the paint work was flaking and missing in some places, there were scratches and marks all over the place. One of them would need the whole chassis resprayed.

Now the problem is matching the paint and trying to keep the original colour and screen prints, this is what I wanted to do, to keep them as original as possible.

So the best way I thought to attempt it was to use an airbrush, as the paints you can get for them have come a long way in terms of quality and finishes. I also have various types of air brushes which allows me to paint as I need and wish, basically I can go very lightly and hit certain areas without over spraying etc.

Before:

[img]https://i.**********/nHmX6mg.jpg[/img]

[img]https://i.**********/nrtXc2L.jpg[/img]

[img]https://i.**********/C1kMiWr.jpg[/img]

[img]https://i.**********/dRjamXO.jpg[/img]

[img]https://i.**********/MmAVfyE.jpg[/img]

One of the chassis would need a complete respray! As you can see it looked horrible.

So I used some wet and dry to sand flat the chip marks, scratches and removed the flaky paint around the amplifier.

[img]https://i.**********/xwJDKVt.jpg[/img]

[img]https://i.**********/AIaHYms.jpg[/img]

I cleaned the dirt off with some alcohol based cleaner wiping and cleaning the dirt, old paint and dust off.
After that I carefully masked off the logo, valve bases and screen prints. Preparation is key here for a good finish, take your time.


Next was to use some black based primer to fill the scratches where needed, this was done carefully as I didn't want build too much of a thick layer, I lightly sprayed it on so it gently covered over the chassis, where there were deep scratches, missing paint I used more paint to build it up.

[img]https://i.**********/EKuRFPO.jpg[/img]

[img]https://i.**********/DdEu9nA.jpg[/img]

[img]https://i.**********/BNxywYN.jpg[/img]

[img]https://i.**********/V22VhIe.jpg[/img]


Mixing the paint to match the colour took time! But I managed to almost get a perfect match!

[img]https://i.**********/HQFP4W1.jpg[/img]

[img]https://i.**********/em1IUpR.jpg[/img]

After it was all prepared, primed and cleaned I carefully blended and layered the paint!


Afterwards: It still needs a few touches here and there, I could also lay a MAT or SATIN varnish which would give it a nice metallic shine and finish it off. Still deciding this, I'll let it dry for 24 hours and see what it looks like, but so far I think you'll agree its 10 times better then what it was!

Next I have to sort the transformers and replace the black tape cover, can anyone recommended a suitable replacement? All in all a good day's work!

[img]https://i.**********/7j4INLY.jpg[/img]

[img]https://i.**********/MleMd7C.jpg[/img]

[img]https://i.**********/cZWpm0n.jpg[/img]

[img]https://i.**********/AHyYsvn.jpg[/img]

PJL 15th May 2018 9:50 am

Re: Repainting my leaks tl12 plus! Came out pretty good!
 
I would leave the tape as the first thing people look for is the original tape and markings as this indicates the transformer has not been rewound.

vishalk 15th May 2018 10:05 am

Re: Repainting my leaks tl12 plus! Came out pretty good!
 
True, although I could just specify they have never been rewound? Otherwise it just looks unfinished. Anyway I'm keeping these for years to come, and they will always go up in value.

marconi_pete 17th May 2018 1:25 am

Re: Repainting my leaks tl12 plus! Came out pretty good!
 
You've done a brilliant paint job on that chassis. Well done. I'd also say leave the tape on, especially if you plan to sell it on at a later date. Authenticity and originality always command higher prices among collectors and enthusiasts.

Thanks,
Peter

vishalk 17th May 2018 9:29 am

Re: Repainting my leaks tl12 plus! Came out pretty good!
 
Thanks Peter, my thoughts were for the future an enthusiast would want a good example to purchase.
I'm guessing this is the general feeling to keep the original tape, right I'll clean it up and glue where it has come away. Hopefully making it look better then what it is.

Thanks

vishalk 6th Jun 2018 3:38 pm

Re: Repainting my Leaks TL12 plus! Came out pretty good!
 
4 Attachment(s)
Finally finished these, sprayed a few coats of varnish and they came out almost good as new! Wonderful :clap:

dave walsh 6th Jun 2018 4:35 pm

Re: Repainting my Leaks TL12 plus! Came out pretty good!
 
Show room quality I'd say. Use photo 2 for the Brochure:thumbsup:

Dave

Al (astral highway) 6th Jun 2018 9:40 pm

Re: Repainting my Leaks TL12 plus! Came out pretty good!
 
Yep, awesome job!

And yes, do keep the original tape. All these details help establish authenticity. I like how the lams in one of the photos are coming apart: these are the kinds of things that show this is the real deal.

I can imagine being a future collector, say in 20 years time, and that's the kind of thing I'd be looking for - a real thing that's been bashed around, loved, used intensely, and then lovingly restored.

(And I'm saying this as someone who restored a few of these before the current bubble in prices!)

Nice one, keep it real!

Nanozeugma 6th Jun 2018 10:47 pm

Re: Repainting my Leaks TL12 plus! Came out pretty good!
 
Superb restoration. Those ECC81 nipples look like a witches tit though ;)


All times are GMT +1. The time now is 6:56 pm.

Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.