UK Vintage Radio Repair and Restoration Discussion Forum

UK Vintage Radio Repair and Restoration Discussion Forum (https://www.vintage-radio.net/forum/index.php)
-   Forum Announcements and Comments (https://www.vintage-radio.net/forum/forumdisplay.php?f=18)
-   -   The Thanks Thread (https://www.vintage-radio.net/forum/showthread.php?t=60832)

Panrock 18th Mar 2012 10:35 pm

Re: The Thanks thread.
 
No sooner said than done! See the Television section:-

https://www.vintage-radio.net/forum/...ad.php?t=81446

Steve

David Pannell 19th Mar 2012 5:14 pm

Re: The Thanks thread.
 
I should like to register my appreciation for the repairs carried out by Forum Member, Ron Bryan, to my DM64 Telequipment storage oscilloscope.

I have had this instrument, along with its smaller sister, the D54 (non-storage) for many many years, when it began to drift out of focus whenever a signal was applied. No signal - razor sharp focus!

During a purely fortuitous conversation with Ron, I learned that he had experience with fixing scopes.

To cut a long story short, Ron fixed it perfectly in a short space of time, and I have to say I am delighted with the result. Further, he found a couple of other problems which he also fixed.

Once again, Ron, MANY THANKS!

Nickthedentist 30th Mar 2012 12:33 pm

Re: The Thanks thread.
 
Thanks to ppppenguin for sending me two Bulgin IEC mains inlets;

to Grim Josef for a mint AT6 template, a nice chat and lovely coffee;

and Herald1360 for a handy Sony circuit diagram.

The generosity of people here never ceases to amaze me.

Thanks Alanomt for kindly sending me an idler for my Garrard TA Mk II 8-)

Sean Williams 4th Apr 2012 8:01 pm

Re: The Thanks thread.
 
Thanks must go to Mike, Jeremey, and GrimJosef for helping rid me of 100+kilos of test gear!

GrimJosef 19th Apr 2012 7:19 pm

Re: The Thanks thread.
 
2 Attachment(s)
And thanks very much to you Sean and also to Mike (Cobaltblue) and Jeremy (Pamphonica) for the Heiden 30V, 10A supply. You described it I think as a 'hefty lump' and oh yes it is - 25kg and built like the proverbial brick outhouse ! It's a lot of psu for a tenner. And I particularly appreciate Mike's and Jeremy's efforts in heaving it across to me. I did have to hammer one of the chassis side-members and the lid itself square (well, roughly square) so I could get the lid to fit back on again. But despite that the unit came on as soon as I powered it up. Tests with a DMM and a scope showed the output was pleasingly stable and pretty well noise-free ;D.

There was one problem however. Both the voltage and current displays on the front panel were showing significant noise, about 0.4V pk-pk amplitude and appearing to oscillate at a few hertz. I wasn't too worried because the supply itself was working fine but it was irritating. I contacted Heiden but they have no schematics or manuals dating back that far (1988 I think). So I just had to start taking the thing to bits. Fortunately the problem was easy to spot. The arrowed component on the second card in (see pic - maybe some kind of clock crystal ?) had half fallen out of its sockets. Also a track repair on the first card had failed, although that might have happened during disassembly. Anyway I pushed the loose legs of the 'crystal' back in and resoldered the track bridge and all now seems well :thumbsup:. So thanks again folks !

Cheers,

GJ

michael cumming 20th Apr 2012 4:08 pm

Re: The Thanks thread.
 
I wish to thank two members on here and they are Whyperion and AC/HL Bill for the batteries they have sent me. Whyperion my 126 Ever Ready range is now complete and Bill thanks for that little Ever Ready 154 inner box. :clap:

Miguel Lopez 23rd Apr 2012 4:31 pm

Re: The Thanks thread.
 
I want to thank again to Andy (aka Dr Wobble) for sending me some valves that I need to continue learning about valve electronics. Now I have them in my hands and I intend to use them in some projects and experiments.

I also want to thank again to all of the forum members who had contributed with those components for me.

Thank you all. Bless you. :thumbsup:

robjkmannering 12th May 2012 8:52 pm

Re: The Thanks thread.
 
A big thanks to ReelToReel for allowing me into his workshop and taking some treasure home. Many thanks also for the radio that looks like it is a 3 valve + rectifier TRF.

Hope to see you at Arminghall over the Summer.
Rob

Cobaltblue 12th May 2012 9:24 pm

Re: The Thanks thread.
 
There are two forum members I would like to thank.

I would like to thank John 60oldjohn.

John not only collected a Cossor for me, he held onto it for several months. When I did finally pick it up I got a very enjoyable evening admiring his rather lovely and beautifully displayed collection.

I was was very impressed with the fine work he does in his restorations.

Unfortunately his internet has not been working for quite some time now, the good news is when he does return he will have no doubt done some more fantastic work.

Thanks John I hope I am able to visit again soon. :thumbsup:


Also I would like to thank Mike A, coil1234 for the Norbit module which arrived during the week and is a blast from the past.

Thank you Mike its a lovely item and will go with well with my semiconductor display. :thumbsup:

Cheers

Mike T

robjkmannering 14th May 2012 2:53 pm

Re: The Thanks thread.
 
Many thanks to forum member Danny who I bumped into at the local car boot and a number of very nice Roberts sets, a Dynatron Tourist, Decca TP88 and others changed hands.
Several red Roberts sets are cluttering the house waiting to jump out on my unsuspecting wife!
Danny also kindly put some sets aside for me whilst I begged my wife for more pocket money.

Regards,
Rob

Nickthedentist 29th May 2012 11:33 pm

Re: The Thanks thread.
 
Thanks to kevinb for taking the time to pack up and wait for my courier to pick up the Pye radio I bought from him. It's in fantastic cosmetic condtion and worked straight out of the box too :thumbsup:

Nickthedentist 13th Jul 2012 3:31 pm

Re: The Thanks thread.
 
Thanks to Steve (music-centre), whose packing skills are first rate.

The huge and heavy Marconiphone radio he sent me really was packed so well that it could have been dropped from 6' onto the pavement and not suffered in the slightest. Easy enough to do for a light and little set, no mean feat for one of these, which is almost the size and weight of a 20" CRT telly.

Nick.

GrimJosef 5th Sep 2012 3:14 pm

Re: The Thanks thread.
 
Thanks to Alec (apowell) for the Chas Miller book https://www.vintage-radio.net/forum/...ad.php?t=87773 and especially for delivering it to my door!

Cheers,

GJ

tis your junk 17th Sep 2012 7:24 pm

Re: The Thanks thread.
 
I'd like to thank Paul for all his work in maintaining this web site and the servers etc that are invisible to most people. I have to admit I don't Know the full story but I do understand that a fair amount of balancing of "Work and play" was required.

I hope the new system works well and we can all enjoy this active forum for years to come.

WELL DONE PAUL (and the committee) :clap:

TYJ

Nickthedentist 18th Sep 2012 3:50 pm

Re: The Thanks thread.
 
Seconded!

Also to Jeremy (Pamphonica) and Sally for their immense patience :-[

Nick.

crackle 18th Sep 2012 9:03 pm

Re: The Thanks thread.
 
Excellent job Paul.
Mike

robjkmannering 18th Sep 2012 9:15 pm

Re: The Thanks thread.
 
A job well done!
Thanks Paul for the continued hosting of this goldmine of information and advice.

Rob

jay_oldstuff 18th Sep 2012 10:32 pm

Re: The Thanks thread.
 
Wow that was fast, well done Paul

Top Cap 18th Sep 2012 11:05 pm

Re: The Thanks thread.
 
Well done Paul, a very hearty thanks for your superb efforts and a well deserving pat on the back!
Les

HamishBoxer 20th Sep 2012 1:16 pm

Re: The Thanks thread.
 
Thank You for speed in which recent changes have been done.

David


All times are GMT +1. The time now is 4:09 pm.

Powered by vBulletin®
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright ©2002 - 2018, Paul Stenning.